Model #11091320100 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control And Rear Panel
    3 Results
  • Water System
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Gearcase
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

how to take out agitator to clean out washer 11091320100 Kenmore Automatic washer

A:

Thank you for your inquiry on your Kenmore Washer, Model: 110.91320100. From reviewing the details on your model, I have included a link to a couple of videos on similar model of washers, which should be able to advice you on how to remove the agitator. The link is found below.

Click Here

Safety Warning: Before beginning the repair, disconnect the direct power supply to the washer to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
April 25, 2015
Q:

hole in diaphram 11091320100 Kenmore Automatic washer

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your washer. Upon researching 11091320100; being that the part is not listed it is not an item that could be replaced by itself. You would have to replace the part it is affixed to.

If you have any further questions please re-post. We appreciate your business. Have a great day.

.

Read More
Jeff Wallace Jr -
Sears Technician
October 01, 2014
A:

Thank you. upon further inspection I find the projection on the outer tub plasti-welded in place. Perhaps it can be accessed from within upon removal of the inner tub but the diaphragm or whatever mechanism is inside is also not listed as a part so it is a moot point. Since their is not enough of a pressure change to trigger the switch to shut off the water, I backed out the screw that sets the water level approx. two turns. Setting for a lower water level means the switch is more sensitive to pressure change. This worked and the water shuts off at the proper levels.

Read More
Howard -
October 02, 2014
See more answers
Q:

Broken timer knob help? 11091320100 Kenmore Automatic washer

A:

I can understand how important it is to have the right information for your washer. There are only two parts that you will need to replace the knob. The knob itself (#388026) and the clip (#285607). I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
October 09, 2013
Q:

93 Kenmore washer ONLY agitates on every setting. No water coming in. checked pressure line, all good.

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina -
June 29, 2013
A:

Thanks for contacting manage my life about your washer model 11091320100, sorry you are having a problem I will be glad to assist you with this issue. Based on your description of the issue I suspect the water level switch has stuck contacts. If this happens the washer thinks it is full of water and will agitate without allowing any more water into the tub. I have attaché an image below that will help you test and check the water level switch. .I hope this helps If you need more help reply with added details and I will be happy to respond.  If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.Ron H.

Read More
Ron H -
Sears Technician
July 01, 2013
A:

Yesterday I took the pressure hose off, put it back on and the water entered the washer again. Today, low level wash taking place, went in to put fabric softener in rinse and washer had overflowed on floor. I need to know what switch controls this and where in my area can I purchase this part? Cold water only, is continuing to come into washer. I can fix this myself without calling for service if I can only locate the parts I need.

Read More
Cathy -
July 01, 2013
A:

Hi Cathy, Here is a link to parts; Sears Parts Direct I have no access to a local parts supplier in your area. (Note pulling pressure hose off during a cycle will cause fill issues, removing and reinstalling the hose should only be done when washer is not in use.) . Ron H.

Read More
Ron H -
Sears Technician
July 02, 2013
A:

Hi Ron, We did wait til washer was finished. We unplugged and took apart washer correctly. Do you have a diagram of how I'm too replace this part I need? What is the part number and decription of the part I need to replace to regulate the water level. Thanks. Cathy

Read More
Cathy -
July 02, 2013
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show