Model #11091264100 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Wiring Harness
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Gearcase
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

tub not turning 11091264100 Kenmore Automatic washer

A:

Thank you for contacting SearsPartsDirect.com with your question about your Kenmore Washer model 11091264100. I am so sorry the tub is not turning. I know how quickly the laundry can pile up when the washer isn't working and I know you want it fixed as soon as possible. I will be happy to help you with this.
 
There are several issues that can keep a washer from spinning. I have included the blue link below to our repair help guide. I will outline the parts you should check for damage. Once you determine the issue, check the repair guides and there will most likely be a guide that can walk you through the repair.
 
 
Safety Warning: Be sure to disconnect the power to the washer before you begin testing parts to prevent injury from electrical shock. 
 
Check the lid switch. This is a safety device that keeps the washer from spinning if the lid isn't closed. Also check the water level switch. The washer will not spin if there isn't enough water in it. You can test the switches with a multimeter. The switches should have continuity, otherwise the part needs to be replaced. I have included the blue links below to order the switches in case the test shows one of them is the problem.
 
 
If the switches are fine, you will want to check the motor coupler. This part breaks to protect the motor whenever the basket is overloaded or off balance. You will need to visually inspect the part to see if it is the problem. I have included the blue link for that part also.
 
 
If the above tests have not identified the issue, then you will need to check the Clutch Drum. If the washer will spin without a load of clothes, but otherwise will not, then you may need to replace the clutch drum. If the clutch is okay, then the problem is most likely the gearcase. Because these parts require "live" wire (electrical power connected) testing, you may want to have the washer serviced by a technician. If you would like to set up service, you can do that at www.SearsHomeServices.com or by calling 1-800-469-4663. 
 
I hope this answers your question. If you need further assistance, please resubmit your question with additional details. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
June 17, 2014
Q:

washer fill cycle not working 11091264100 Kenmore Automatic washer

A:

Thank You for contacting SearsPartsDirect.com. I do apologize for the delay in answering your question.

I understand your frustration when you washer isn't working correctly. Based on the information you provided I believe either you have a problem with the pressure switch (water level switch) or the timer.
The pressure switch tells the machine when the tub is full to prevent the tub from over flowing. The pressure hose can get clogged or the switch can malfunction.
The timer tells the unit when to fill with water, agitator and spin. If the timer may not be sending the correct signals.
In this situation it is more common to have a problem with the pressure switch and hose. Only because this is happening during both the wash and rinse cycles.
I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

Water Level/Pressure Switch for Model 11091264100

If you need further assistance please respond below. Thanks for visiting SearsPartsDirect.com

Read More
Desirea -
Sears Technician
March 31, 2014
Q:

Why is the timer not advancing on my Kenmore washer?

A:

From what you are describing it sounds like the timer needs replaced. The only way to confirm the diagnosis is to check the voltage to the timer motor with a volt meter or replace the timer to see if that fixes the problem. If you decide to check it with a meter please get back with us for more specific troubleshooting tips.

Read More
biker dave -
Sears Technician
June 23, 2009

Top Parts