Model #11088752796 KENMORE Laundry Centers/Combos

  • Washer/dryer Control Panel Parts
    3 Results
  • Dryer Front Panel And Door Parts
    3 Results
  • Dryer Cabinet And Motor Parts
    3 Results
  • Dryer Bulkhead Parts
    3 Results
  • Dryer Support And Washer Parts
    3 Results
  • Washer Top And Lid Parts
    3 Results
  • Washer Cabinet Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Tub And Basket Parts
    3 Results
  • Water System Parts
    3 Results
  • Gearcase Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Product Accessory Parts
    3 Results
  • Miscellaneous Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Washer problem

A:

Having a properly working washer is very important. I did some research on your model number but was not able to find a solution. Your expert will be able to help answer your question. It may take two business days for your expert to reply. If you would like to look into Sears doing the repair here is a link for Sears Home Services. I do hope that everything works out on the Kenmore laundry unit.

Read More
Marc -
July 24, 2013
A:

Thank you for your question. By the description you have provided it sounds like your lid switch is bad. It could be your timer as well. I advise you to check the lid switch first. Doing it in steps will save you money. 

The washer cabinet will need to be removed in order to access and replace the lid switch. See images below.


First, disconnect the power cord from the power source.

The console will need to be placed in the service position by removing two (2) hidden screws, one (1) screw is located at the bottom of the left hand end cap  and one

(1) screw is located at the bottom of the right hand end cap. In order to access these two

(2) hidden screws, the left hand end cap trim  and under the right hand end cap trim will need to be removed.

To remove the trim, place you finger behind the trim at the very top and bend it up enough to clear the console and then hinge it towards the front and off.

Remove the hidden screw under each end cap trim. Slide the console forwards about 1/4 inch and the raise it upwards and hinge it over the rear panel.

Disconnect the 3 wire lid switch harness plug located on the top. Pop the two (2) gold colored cabinet retainer clips off.

Place the tip of a flat tipped screw driver down into the first valley and then push the handle end to the rear of the washer to pop off the cabinet clips.

Open the lid and grab the opening and tilt the top of the washer cabinet forwards just a few degrees and then walk it backwards and off.

The lid switch mounted under the main top is now accessible to remove and replace.
Reverse the procedure to re-assemble the washer.

After accessing the console area start the washer in a spin cycle. Place the multi-meter on volts A/C and carefully place the meter leads across the 2 wires coming from the timer motor. If you read 120 volts then you will need to replace the timer.

Timer part number 3406723
Lidswitch part number 3355806

Get all your parts at www.SearsPartsDirect.com

Reply to this post if you have any more questions.

Thank you for choosing manage My Life.

Read More
dtova00 -
Sears Technician
July 25, 2013
A:

I have the same issue, fills up then has a little hum, but does not agitate.

Read More
Jacob -
July 03, 2015
See more answers
Q:

How do I open the washer cabinet to see where I have a leak. 110.88752796

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist in getting access to the inside of your washer. 

To remove the service panel:
1. Remove 1 screw from the top left and top right
corners of the service panel.
2. Lift the service panel and pull it forward to
release the panel from the cabinet.

To remove the front panel:
Note: In the following step, removing the dryer door
allows for easier manipulation of the dryer front
panel.
1. Remove the bottom screw from each hinge and
loosen the top screw, then lift the door off the
dryer front panel.
2. Remove the service panel. 
3. Remove the 2 Phillips-head screws and the heat
shield from the cabinet.
Note: In the following step, cover the top of the
washer with a protective surface.
4. Disengage the control panel from the front
panel, then place it on top of
the washer.


To remove the cover assembly:
1. Remove the front panel. (See Front Panel.)
2. Remove the two 1/4-in. hex-head screws that
attach the cover assembly to the washer.
3. Lift the cover assembly approximately 4 inches,
open the lid, and then remove the 2 Phillipshead
screws that attach the lid lock.
4. Reach under the cover assembly, and then
fi rmly press in on the front lock tab to release
the lid switch. Push it up from the opening in the
cover assembly.
5. Pull the cover assembly from the washer

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
June 10, 2015
Q:

Stackable Dryer Problem 11088752796 Kenmore Laundry center

A:

Thank you for your inquiry on your Kenmore Laundry Center, Model: 110.88752796. From reviewing the details on your model, this can be a do-it-yourself project but you will need a volt meter and be confident in its use. If the belt was broke the motor would not try to work at. What I'd suggest first is to access the motor, see image below, and make one check. I don't usually suggest a live voltage check but it is the check that needs to be made. With the dryer unplugged you can access the motor and set up to check voltage from the blue wire to white/red wire when the push to start button is pressed. If there is 120 volts then the motor is bad. Use caution doing this.

Safety Warning: Before beginning the repair, disconnect the direct power supply to the laundry center to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
April 23, 2015
A:

Just wanted to report that I fixed the problem. The blue and the violet wire were switch on the timer. Being that this was a new unit from the factory I overlooked the obvious, especially when the terminals are clearly marked.

Read More
Dan -
April 24, 2015
See more answers

Top Parts