Model #11088675110 KENMORE Laundry Centers/Combos

  • Washer/dryer Control Panel
    3 Results
  • Dryer Front Panel And Door
    3 Results
  • Dryer Cabinet And Motor
    3 Results
  • Dryer Bulkhead
    3 Results
  • Dryer Support And Washer Cabinet Harness
    3 Results
  • Washer Top And Lid
    3 Results
  • Washer Cabinet
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Tub And Basket
    3 Results
  • Washer Water System
    3 Results
  • Sales Accessory (lck 4500)
    3 Results
  • Sales Accessory (lck 4600)
    3 Results
  • Misc. Parts Bag
    3 Results
  • Gearcase
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Washer Lid Switch 11088675110 Kenmore Washer/dryer

A:

Thank you for your inquiry on your Kenmore Laundry Center, Model: 110.88675110. I’m so sorry you’re having trouble with and will be happy to see what might be causing the issue. On reviewing your model, I have provided a link to a couple of videos on similar models of laundry centers which should be able to assist you on replacing the lid switch.

Click Here 

Safety Warning: Before beginning this repair, disconnect the power supply to the laundry center to prevent risk of injury from electrical shock.

Caution: internal parts may have sharp edges that may cause serious cuts. Use caution and wear protective gloves if possible.

If you’re not feeling confident/comfortable repairing this problem yourself, you could have it repaired by a sears technician at your home. Here is the link and phone number for our technicians. Sears Home Services or-1-800-469-4663. 

 

I hope this answered your question. Thank you for choosing SearsPartsDirect.com and have yourself a wonderful rest of your day. 

Read More
Gerry 93 -
Sears Technician
June 09, 2015
Q:

No cold water

A:

Having a Washer that doesn't work properly can be quite frustrating especially if its an appliance we use on a daily base. While you are waiting on an expert to answer your question, I was searching your question in the Manage My Life website and found this great link on why Washer won't fill with cold water. I attached the link below. Hope this is useful!

Read More
Dezeray S -
November 20, 2010
A:

Thank you for your question and model number. Based on your symptom and details the water inlet valve assembly has likely failed or the inlet filter screen is completely restricted located inside the water inlet valve assembly. I recommend sliding the laundry center away from the wall and turn the cold water supply faucet off. Disconnect the cold water fill hose from the back of the washer where it connects to the water inlet valve. After removing the hose, place the hose in the washer tub and turn the cold water supply faucet ON to confirm cold water flow and volume. If you have a good flow of water, replace the water inlet valve.

To access the water inlet valve:

  • Disconnect the power cord from the power source.
  • Remove the two screws located at the top of the diagonal panel located between the bottom of the dryer and the top of the washer.
  • Remove the diagonal panel.
  • Lean over the top of the washer and remove the screw at each rear top corner of the top securing the hinges.
  • Slide the top backwards and disconnect the lid switch harness and remove the top.
  • Look in the upper left rear corner and you will see the water inlet valve where the hot and cold water hoses connects.
  • Remove the hot and cold water fill hose.
  • Remove the two screws from the rear of the washer securing the water inlet valve.
  • Disconnect the wire connections and loose the clamp
  • You will see a large clamp that must be squeezed open and then slid back away from the valve.
  • Remove the old valve and reverse the procedure to install the new water inlet valve.
The water inlet valve is part #285805 and is available to order at Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . The service call will be approximately $130.00 which includes the labor but not parts.

Read More
Joey S -
Sears Technician
November 20, 2010
A:

THANKS! Perfect answer.

Read More
Anonymous -
November 22, 2010
A:

Thanks for the reply and I'm glad to be of assistance.

Read More
Joey S -
Sears Technician
November 22, 2010
A:

i have a 2003 he3t washer that is not giving cold water...it was working prior to our moving. what is wrong?

Read More
Maryelyn1 -
March 24, 2011
A:

Marylelyn1: If cold water was entering before the move I would suspect it could be the lack of cold water. Turn the cold water off, remove the fill hose from the back of the washer and place the end of the hose in a bucket. Hold the hose down into the bucket and then turn the cold water faucet on and confirm water flow and volume. If you confirm plenty of water pressure and volume then I would suspect a faulty water inlet valve or there could be slight possibility a wire may have come loose connected to the cold water inlet valve during the move.

Read More
Joey S -
Sears Technician
March 25, 2011
A:

thanks, joey. already tried your suggestions. so, how do we replace the "faulty water inlet valve"?... or repair the "wire" that may have come loose? mary

Read More
Maryelyn1 -
March 25, 2011
A:

Maryelyn 1: I added an image with instructions on how to replace the water inlet valve. Trace the wires attached to the water inlet valve and check for loose connections where they connect to the control board. Be sure to disconnect the power cord from the power source before removing the top.

Read More
Joey S -
Sears Technician
March 25, 2011
A:

hi joey...will try this tomorrow. i couldn't figure out how to locate your suggestions to me so I just typed in another question. Haven't got the hang of this yet. So if you see my question again, it's not 'cause I didn't appreciate your answer. Please help me all you can 'cause I have no funds for repair. House foreclosure and bankruptcy has left me dry. thanks...Mary..I will let u know if your suggestion works.

Read More
Maryelyn1 -
March 27, 2011
See more answers
Q:

Is dryer installed at 110 volts or 240 volts? Can I tell by looking to the plug?

A:

Knowing what the appliances need to operate properly is important. The owner's manual normally has the voltage requirements. I was not able to find the manual for your model but I did find another post dealing with required voltage for a Kenmore stacked dryer. I attached the link below. This may help while you wait for the expert answer.

Read More
Barbara H. -
August 01, 2010
A:

According to the model number this dryer is rated for 220volts. Be sure to reset the house breakers before calling for service; an electric dryer will run but not heat if one of the double 30 amp breakers trip. Please see the image provided below showing a 220volt dryer cord & wall plug. Remember to disconnect power before attempting to remove panels or replace parts & use _extreme caution _ when working around voltage.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
biker dave -
Sears Technician
August 03, 2010
See more answers

Top Parts