Model #11087592100 SEARS Laundry Appliances Division (26)

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore dryer Model # 110.87592100 Will not start.-

A:

Diagnosing dryer problems can be challenging. I see you have ruled out at least two possibilities. While you wait for the expert to review your model for a specific answer, you might check a previous expert post for some ideas. I attached the link below along with the link to Sears Parts Direct if the schematics or parts are needed. I hope this information helps.

Read More
Barbara H. -
September 29, 2011
A:

I have a wiring diagram for that dryer but it is on microfiche. It is shown in the first image below with that motor circuit traced in red. Based on the component checks that you have already completed, the problem seems to be in the part of the circuit that is traced in yellow on the second image. You could have a failed timer contact, a bad drive motor or a wiring failure in that part of the circuit. You can check for continuity through that drive motor (5M to 4M on the motor switch). If the motor is okay, I recommend that you check the wiring. The next step would involve live voltage checks. I don't recommend that you perform live voltage checks yourself unless you are completely confident in your technical ability to safely complete them. Here is a link for the Sears Service website in case you need it: Sears Home Services .

If you are able to check voltage, you can check to see if you have voltage at the motor. If not, you can check it at the yellow wire on the timer. Use that wiring diagram to determine where you are loosing voltage if necessary. NOTE: Use extreme caution when conducting live voltage checks. Do not make contact with any live components. Unplug the dryer as soon as the live voltage checks are completed . As noted above, have a service technician diagnose and repair the dryer if you are not confident that you can safely conduct the voltage checks.

These tips may help you diagnose and repair the dryer. If you need parts, you can order them from the Sears PartsDirect website.

If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
September 29, 2011
A:

I have a Kenmore dryer and it won't run and the drum light doesn't turn on. I replaced the bulb and the light still doesn't work. What can I check?

Read More
Anonymous -
September 30, 2011
A:

Thanks for all the suggestions, but I have made the decision to "Give up the Ghost" I have owned my Kenmore Dryer for 27 years and it's time to buy a new one. After 27 years of sucessful service, I will certainly consider another Kenmore/ Sears Dryer and if it last as long as the one I purchased 27 years ago, I will not have a need for dry clothes anymore - Thanks for your technical assistence. A loyal Sears Customer

Read More
John Roberts -
October 01, 2011
A:

Hello Mr. Roberts. Thanks for those comments and for being a loyal Sears customer. The current models of Kenmore dryers should last nearly as long (or maybe longer) that the one you had. Let us know if you ever need more help.

Read More
Lyle W -
Sears Technician
October 03, 2011
A:

For the Anonymous writer in the above post with the dryer that won't start and the drum light not working: I recommend that you check to make sure that the dryer is plugged in properly. Check the house circuit breaker or fuses for the dryer outlet. If you find no problems with those issues, you could have bad door switch. If you need more help, reply with additional details and the full model number of your Kenmore dryer.

Read More
Lyle W -
Sears Technician
October 03, 2011
See more answers
Q:

Timer problem with Kenmore Gas Dryer - Model #110.87592100: Timer quit rotating on "Timed Cycle" but would rotate on "More Dry, Less Dry, Wrinkle Guard"

A:

I understand that you are having problems with your timer not rotating on a timed cycle but on the others it does. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view. I hope the link that I provided is helpful. Have a nice day.

Read More
Alina F. -
August 12, 2011
A:

Hi John,

Thank you for submitting a question to Manage My Life. I know how frustrating it can be when appliances do not function properly.

From your description other than wiring it would have to be the control (part number 3398084). This is of course assuming the new timer is good. The timer motor gets L1 from that board and a constant neutral. I recommend re-checking the wiring and if that is good you most likely need a control. Further diagnosis of this issue will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have an ohm/volt meter and are confident in your technical abilities, please reply below and I will be happy to give you the checks.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
August 12, 2011
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show