Model #11087582601 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • Door Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What is error code F 01 11087582601 Kenmore Residential dryer

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is trouble with the dryer.
 
Glad to help out.   Im  looking at your Kenmore model number 110.87582601.

I see  you have the F-01 error coce which the Technical manual states it is a PRIMARY CONTROL FAILURE:

F-01 flashes when there is a primary control failure.  Replace the electronic controls.

1.  Unplug the dryer and or disconnect the power.

2.  Remove the two rear screws from the top panel, and slide the top panel to the rear to remove.

The Main control electronics is right there behind the panel control.

1.  After locating the machine electronic control, remove the two screws that hold the control to the bracket.

2.  Slide the bracket over the top of the drum to access the machine control connectors and mounting screws.

3.  Remove all the wire connectors

4.  Remove the screw holding the control to the mounting bracket.

5.  There are two plastic legs on the front of the control that slide under the mounting bracket.  There is one plastic leg on the rear of the electronic control that slides under the mounting bracket.  There is a locking tab on the bottom that snaps into the mounting bracket.  Press the locking tab on the bottom of the control board and slide the assembly  to the front, then lift.

Control board for model 110.87582601

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
February 17, 2014
Q:

Kenmore HE2 electric dryer model 110.87572601 that has stopped heating

A:

I'm sorry to hear that you are having some difficulties with your Kenmore HE2 Electric Dryer. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
James -
November 08, 2011
A:

Thank you for your question and I understand your concern.

Be sure your dryer is getting the proper voltage supply of 220 volts or it will run but not heat. NOTE: I do not recommend checking voltage unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your dryer. You can jump out the thermal fuse but you can't jump out the thermistor. NOTE: Disconnect the power cord from the power source before servicing your dryer. The thermistor is neither shorted nor open. It has resistance that changes with temperature. If you jump out the thermistor; the control board would think it was shorted because it would be.

I added three images below that will have the entire trouble shooting steps to diagnose why your dryer is not heating.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
November 08, 2011
A:

Hello I have the same symptoms on my Kenmore 110.87582601 dryer. I have tested the thermal fuse and it has continuety. The Thermister does not have continuity. I can here the relay on the board slicking when I hit the start button and it clicks again when I hit stop. but the motor will not turn. any Ideas?

Read More
tim -
January 30, 2012
A:

Tim: Based on your details, if the thermal fuse has continuity and the belt is not broken, it sounds like a faulty control board even though you hear the motor relay clicking closed. When the relay closes, you should measure voltage across P9-1 and P8-3 and voltage across P9-1 and P8-4. If you do not measure 120 volts, the control is faulty. If you do not have your Ohm meter set correctly, it may show the thermistor open. The thermistor should measure approximately 11.9 K Ohms at 70 degrees. You can not jump across the thermistor or the control will display a fault code indicating a shorted thermistor. Do not jump the thermistor.

Read More
Joey S -
Sears Technician
January 31, 2012
A:

OK measure 12 ohms on the thermister and have voltage 126 volts. Do you think it could be the motor?

Read More
tim -
January 31, 2012
A:

Tim: If you measured 126 volts between P9-1 and P8-3 and voltage across P9-1 and P8-4 then the control board is okay. The next component to disconnect and test for continuity is the thermal fuse. If the thermal fuse is faulty, the motor will not start. The thermal fuse will be located next to the thermistor.

Read More
Joey S -
Sears Technician
January 31, 2012
A:

I tested it and it has continuity

Read More
tim -
January 31, 2012
A:

Tim: There is also a broken belt switch connected in series between the thermal fuse and motor and if the belt is off or broken, the motor will not start.

Read More
Joey S -
Sears Technician
January 31, 2012
A:

the belt is on and in OK shape, the tensioner seems ok also.

Read More
tim -
January 31, 2012
A:

Tim: Have you checked the voltage at the motor? If you measure 126 volts at the motor across terminal 4M and 5M and the motor is not humming or starting, the motor would have to be faulty.

Read More
Joey S -
Sears Technician
January 31, 2012
See more answers

Top Parts