Model #11087531700 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • Door Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Error code F1 on Kenmore HE2 electric dryer appeared; replaced ERC as suggested; F1 error code is still there. What more can I do?

A:

I understand that you are getting the error code F1 on your dryer. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view. I hope the link that I have provided you is useful.

Read More
Alina F. -
November 14, 2010
A:

Alina, Thank you for your answer. We did unplug, etc., as suggested in the attachment in your post. I have noticed that the touchpad on my dryer will not allow cycle changes, etc. I am now wondering if we have a malfunctioning touchpad. I do not know. Please keep looking. This is perplexing. Thank you.

Read More
Librarian9303 -
November 14, 2010
A:

I recommend that you double check that model number and make sure that you have the correct electronic control board installed in the dryer. The part number of the control board for model 110.87571601 should be W10111606.

If the correct control board is installed, then you could have a bad replacement control board or another problem that is preventing the control board from working properly. On a few of the HE types of dryers, there has been an unusual issue that has caused some intermittent F01 error codes. A short in the moisture sensor wires has been known to cause this error code. I provided a wiring diagram for this dryer in the image below. You can unplug the dryer and access the control board. Unplug the moisture sensor wires from the control board and then reassemble the dryer. Power it back up and see if you still get the F01 error code. If not, then I recommend that you carefully check the moisture sensor wire harness for a short to the metal cabinet.

There is a possibility that you have a bad touchpad that is causing this problem. If the above steps don't help, you may need to try replacing that component.

I hope that these tips help. This may be a difficult failure to diagnose. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

If you need more help, reply with additional details and we will try to assist you further.

Read More
Lyle W -
Sears Technician
November 16, 2010
A:

So, I am having the same problem, but have not started to try anything yet. What should I try first?

Read More
michelle -
February 27, 2013
A:

Hello Michelle. Reply with the full model number of your dryer. If you are seeing the F1 code on an HE2 dryer, then you can try unplugging the dryer for 5 minutes. Plug it back in and see if the code clears and the dryer works properly. If not, then you may need to replace the main machine control board. If you reply with the full model number and additional details, we will try to give you some more specific troubleshooting help.

Read More
Lyle W -
Sears Technician
February 27, 2013
A:

Thank you! Model # is 11087531700

Read More
michelle -
February 27, 2013
A:

I posted an image below that shows the error codes for that dryer. I assume that you are seeing the F-01 code and that it will not clear. In that situation, you will need to replace the machine control board (part W10111606). Here is a direct link for that part: Electronic Control Board for Kenmore Dryer Model 110.87531700 . UNPLUG the dryer before installing that new control board. The image below shows how to access and replace that machine control board in your dryer. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
February 27, 2013
A:

We "inherited" our washer/dryer about 3 months ago and the dryer is now showing the same error message... our model number is 110.87511702. Can you tell me what we should do?

Read More
DENESE -
February 09, 2015
A:

same problem, lights work, hear the click, then nothing happens. Model # 110-87561602. Any help would be appreciated!

Read More
Gretchen -
July 06, 2015
A:

same problem, lights work, hear the click, then nothing happens. Model # 110-87561602. Any help would be appreciated!

Read More
Gretchen -
July 06, 2015
See more answers
Q:

What does code F 01 mean?

A:

I see that you want to know what the error code F01 means. If you would provide a model number I would be able to give you the exact answer that you are looking for since many different appliances can set off the same error codes as other appliances, but I have searched on Manage My Life for an answer and came up with a list of possible answers that can help you identify which error code belongs to your appliance. I have attached the link below. Hope this helps!

Read More
Alina F. -
October 08, 2010
A:

On most washers the F01 error indicates an control board problem. It is like an internal program error.

A power glitch can cause the problem.

One of the things to try is to enter and run a diagnostic cycle.

If you can supply a model number then I can most likely help you with the diagnostic test.

Please reply with a model number for further assistance.

Read More
Fred M -
Sears Technician
October 08, 2010
A:

I am receiving this error code as well. We have taken off the panel and made sure all connections are securely attached to the control panel. I have an HE2Plus -- please advise ... thank you! Stephanie

Read More
steph223 -
July 11, 2011
A:

I can help but a model number is needed to give you specific things to try.

Read More
Fred M -
Sears Technician
July 11, 2011
A:

It's the Kenmore HE2PLus WAsher, Item# 02647531000 Mfr. Model# 4753

Read More
steph223 -
July 11, 2011
A:

here's a link also...

Read More
steph223 -
July 11, 2011
A:

The F01 usually means the central control has failed. The thing to try first is to enter and run a diagnostic test. If it fails to run then you wil need to replace the control. Try the test and let me know how it goes or if it doesn't go.

Read More
Fred M -
Sears Technician
July 12, 2011
A:

I have an HR3 just replaced the fuse, worked great for one load! Now its flashing again F01. heres the model #11087572601. I just spent 269.00 for service, and its still not working!! Can you help me??

Read More
CARLA -
November 18, 2011
A:

Carla, the F01 is a primary control failure and most likely the contol will need to be replaced. The model number you submitted is for the dryer while the previouse questions dealt with a washer. The image below contains the instructions to enter the diagnostic. First try to see if you can enter the test. If you can't then most likely the control will have to be replaced. Let me know how it goes.

Read More
Fred M -
Sears Technician
November 21, 2011
A:

I have a Kenmore He2 model 110.87531701. I have the F01 code also. Ran the diag test all leds came on and F01 fault code.

Read More
bill -
January 02, 2013
See more answers

Top Parts