Model #11087175100 SEARS Laundry Appliances Division (26)

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore gas dryer. the flame goes out after a few minutes then comes back on 11087175100

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your dryer is not working properly.

Click here for testing information on the thermostats and the ignitor itself. This should help you determine which part to replace.

Click here for more information.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
May 28, 2015
Q:

Intermittent ignition 110.87175100

A:

Thank you for choosing Sears Parts Direct. I can certainly understand how frustrating it can be when your dryer does not keep the flame. I did look into the model number you have provided and I have found information that will assist you in testing which part could be the issue. Click here to view the information. Let me know if this helps,.

 

Thank you for your question. Have a great day.

Read More
Natasha12 -
Sears Technician
November 12, 2013
Q:

What is wrong with a Kenmore model 110.87175100 dryer that does not light up even after the igniter was replaced?

A:

You’re correct the sensor may be causing this problem.

It's hard to pin this problem down but if you've already replaced the igniter then the flame sensor is the next part to check.

The igniter works and gets real bright but after 15-30 seconds the flame sensor should sense the igniter and open the circuit across the sensor.

Two things happen almost simultaneously when the flame sensor opens. The igniter goes out but at the same instance, while the igniter is still bright, the voltage that was powering the igniter is directed to the gas valve. When this happens you may hear a click, buzz, or hum from the gas coils.

If you hear nothing then it may be the coils are the problem. If you hear the buzz, hum or click from the coils but there is no flame then the gas valve may be the problem. The coils can be checked with a volt/ohm meter for continuity if you have access to one and are comfortable using it.

If the igniter glows for a minute and never clicks off then the flame sensor is most likely bad.

The coil assembly is part number 279137 and is available from the following link: Sears PartsDirect .

This can be a difficult problem to diagnose with the front panel on. It's hard to hear the coils and to see what is going on. There is another way to check this problem if extreme caution is used.

This dryer has no belt switch so with the front panel off and the drum and belt removed you can still run the dryer. With the dryer running you can see the igniter glowing and when it clicks off, if it does, and have a better chance of hearing any noises from the gas valve coils.

I hope this information helps to resolve your problem but if you have other questions after making some checks then submit another question with any additional details for further assistance.

Read More
Fred M -
Sears Technician
July 23, 2009
A:

I'm having a similar problem. It is intermittent. After reading above, I removed the front panel of my stacked washer/dryer (model 417.98862890). The igniter will get red hot, a click will be heard, and when normal, a flame will ignite and all is well. When things are not running as they should, the ignitor will get hot, I hear the click, but nothing happens. Does that mean the coils are good, but the valve isn't working? I'd appreciate some feedback, as the coils are only like 30 bucks, but the valve is almost $190. Thank you.

Read More
Carlos -
September 14, 2011
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show