Model #11086864100 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

dryer will notstart 11086864100

A:

Thank you for choosing sears I would be happy to help you with your dryer. Upon researching model 11086864100; it sounds like the either the timer or the push to start switch may have failed, both of this parts have been discontinued and are no longer available.

I trust this information will help you, have a great day.

Read More
CarlosZ -
Sears Technician
February 09, 2015
Q:

Won't turn off when door open 11086864100 Kenmore Dryer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Yadira B -
July 24, 2013
A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

I am sorry and do understand your frustration when having trouble with the dryer.   This dryer predates 1987 so has been around for a good long time. 

This problem you are having is with the door switch.   I will give you the information on the door switch if you just click on the link below.

http://www.searspartsdirect.com/partsdirect/part-number/347207/0026/110&pathTaken=partSearch&blt=14&prst=0&shdPart=347207?sid=MMLxexpertmerch

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
July 24, 2013
See more answers
Q:

Kenmore dryer model 110.86864100 burning fuse

A:

Having a properly working dryer is very important. The fuse burning can be very concerning. I found some information for you that I am hoping will help you until your expert answers your question. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you with the dryer.

Read More
Marc -
September 25, 2012
A:

You probably have a short in that L2 (second hot leg) that is causing that problem. Unplug the dryer and access that terminal block on the back of the dryer. Using a volt/ohm meter, check for a resistance reading between the red wire (L2 leg) and the bare metal of the cabinet. You should not normally detect any resistance value during that reading. It should read OL (open load or infinite resistance) unless you have a short in the wiring to the cabinet ground. If you do detect resistance, I recommend that you check the outlet cord and the wiring between the terminal block and the motor centrifugal switch. You will probably find a short to the metal cabinet in that portion of the L2 circuit. If you do not detect resistance when taking that reading, then you probably have a short in the heating element or the wiring between the motor centrifugal switch and the heating element. Remove the back panel to access the heating element. If that heating element is broken and is shorting out to the metal cabinet, then it will need to be replaced. You can order that heating element from this page: Heating Element for Kenmore Dryer Model 110.86864100

If that element appears to be okay, then you can check the wiring in that portion of the circuit for a short to the cabinet ground in the same manner as described above. You can open the cabinet as shown in this previous answer: how do you get belt on . Inspect the wiring to find the short if necessary.

I hope that this information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician examine and repair the dryer, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
September 26, 2012
See more answers

Top Parts