Model #11086671800 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

dryer failure 110.86671800

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your dryer and do understand your frustration. Glad to help out. Im looking at your model number LER4624BW2 and If the dryer is not heating you could be experiencing an issue with the thermal fuse (3392519), operating thermostat (61894 ), high limit thermostat(341195)and thermostat 660039 . If you have an ohms/volt meter you can test these parts for the proper continuity. To test the parts, disconnect both wires from the components and test them at room temperature. The ohms reading for these components should be zero ohms. If the high limit thermostat is faulty, then replace the thermal cut-off as well and vice versa. They two components work together and come as a kit. If they component listed above test good, then the issue may be with the heating element (4391960 ) and I recommend testing it as well. You'll want to get a reading of 7.8 - 11.8 ohms for it to test good.  I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. If you have further questions please resubmit your question for further information.
 
Thanks for choosing Sears PartsDirect.com.


SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others. 

Read More
Sherman_G_Wallace -
Sears Technician
March 25, 2014
A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your dryer and do understand your frustration. Glad to help out. Im looking at your model number LER4624BW2 and If the dryer is not heating you could be experiencing an issue with the thermal fuse (3392519), operating thermostat (61894 ), high limit thermostat(341195)and thermostat 660039 . If you have an ohms/volt meter you can test these parts for the proper continuity. To test the parts, disconnect both wires from the components and test them at room temperature. The ohms reading for these components should be zero ohms. If the high limit thermostat is faulty, then replace the thermal cut-off as well and vice versa. They two components work together and come as a kit. If they component listed above test good, then the issue may be with the heating element (4391960 ) and I recommend testing it as well. You'll want to get a reading of 7.8 - 11.8 ohms for it to test good.  I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. If you have further questions please resubmit your question for further information.
 
Thanks for choosing Sears PartsDirect.com.


SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others. 

Read More
Sherman_G_Wallace -
Sears Technician
March 25, 2014
See more answers
Q:

kenmore dryer won't start

A:

Hearing buzzing from an appliance's can get really frustrating. While you are waiting on an expert to answer your question, I found this great link in the Manage My Life website. I have attached the link below. Hope this helps!

Read More
Dezeray S -
January 29, 2011
A:

Thank you for your question and I understand your concern. When you state that the dryer will not start and only buzz when start is pushed, I must assume your dryer is making a humming noise from the motor when start is pushed because the motor is not able to start. This is generally an indication of a faulty motor. Open the door and manually rotate the dryer drum in a counterclockwise (CCW) direction for 1-2 revolutions and then shut the door and press start. It may or may not start. If starts, it will likely fail again meaning the motor will need to be replaced.

If you attempt to access and replace the motor, disconnect the power cord from the power source before servicing. I added the basic instructions in the images below.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 31, 2011
A:

I my case only the timer acts like its running n0 motor hum and no heat...

Read More
Robin -
January 05, 2013
A:

It seems to be the timer is bad..

Read More
Robin -
January 05, 2013
A:

It seems to be the timer is bad..

Read More
Robin -
January 05, 2013
A:

Robin: It is possible to have a faulty timer but there are other comonents in the motor circuit which can fail and prevent the dryer from starting. I will need to know the model number of your dryer in order to provide any model specific troubleshooting assistance.

Read More
Joey S -
Sears Technician
January 05, 2013
See more answers
Q:

Noisy Kenmore dryer model # 110.86671800

A:

Kenmore dryers were a great invention but when they make that much noise, you just want to shut it off. The links below may help you understand what is going on with your dryer. An expert will be with you within 24-48 hours. Thanks for your patience.

Read More
Anna T -
June 01, 2012
A:

I know that it can be very frustrating to have issues with your dryer, especially when you need it. The noise that you are hearing can be cause by several components, such as the blower wheel, the drum rollers, or the bearing. The images below will provide the instructions for disassembling the dryer. I would suggest you being with the blower wheel. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
June 03, 2012
See more answers

Top Parts