Model #11086661100 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

drive belt 11086661100 Kenmore Electric dryer

A:

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when looking to replace the belt of your dryer.

Glad to help out.   Im  looking at your model number 110.86661100.
 
There are two ways to get the belts for the dryer.  You can get the belt by itself which you will or can see on the link below.  The best way that I highly recommend you getting though is the belt maintenance kit.   It has the belt, the drum support rollers, with clips and hardware with instructions to do it all.   Turns your dryer back into almost new.   You can order the items from the links below or you can do so over the phone to call Sears Parts Direct at 1-800-366-7278.
 
 
 
 
If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com
 

Read More
Larry L -
Sears Technician
September 16, 2013
Q:

my dryer won't start

A:

When a dryer doesn't work properly it is such a frustrating situation especially when you do not know what is wrong with it. I have taken the time to further your search here on Manage My Life and I noticed that someone else had asked a similar question with a posted response from an expert. I have attached the link below if you are interested in viewing the website while waiting on your response from an expert. Hope this helps, good luck!

Read More
Alina F. -
August 19, 2010
A:

From what you’re describing I suspect the thermal fuse failed. The thermal fuse is a safety thermostat that if the dryer gets too hot will shut the motor down. This symptom is usually caused by a blocked exhaust vent or shorted heating element. First; disconnect power to the dryer & remove the rear panel. The thermal fuse is #57 mounted to the blower housing. The thermal fuse should read closed continuity (0 resistance) on an ohmmeter. If the thermal fuse reads open continuity it will need to be replaced & the venting & heating element checked out. The heating element should ohm out between 8-12 ohms & read open continuity from each terminal to ground. (be sure the wires are removed). If you read a path to ground you will need to replace the heating element also. Remember to disconnect power before attempting service.

Another possibility; timer, door switch or wiring harness problem.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
biker dave -
Sears Technician
August 19, 2010
See more answers
Q:

What does the 120/240 volt plate on my dryer mean?

A:

Basically, it means the dryer requires a 240 volt voltage supply to plug into. The 120 means that there are components inside the dryer that operates on 120 volts and the heating element requires 240 volts to operate. Overall you have 220 volt electric dryer and the newer dryer will operate fine if it's an electric dryer requiring the same voltage supply. Now, the power cord on the new dryer may or may not fit the wall outlet. Dryer cords can be a 3 prong cord or a 4 prong cord. If the dryer cord on the older dryer does not match the power cord on the newer dryer you can swapped out the two power cords so that it will plug into the 240 volt wall outlet.

(See image below for electrical connections and instructions)

Read More
Joey S -
Sears Technician
April 23, 2009

Top Parts