Model #11085091400 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • Door Parts
    3 Results
  • Pedestal Parts (not Included) (for 15 1/2`` Pedestals
    3 Results
  • Pedestal Parts (not Included) (for 13`` Pedestals Only
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Side vent 11085091400 Kenmore Residential dryer

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about changing the venting on your Kenmore dryer model 11085091400. I will be happy to help you with this.

Your dryer can be modified to vent from either the side or the bottom. I have included the link below for the venting kit. It will include the parts you need to change the vent location and will come with the step-by-step installation instructions.  

Dryer 4-Way Exhaust Vent Kit

I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
November 05, 2014
Q:

Control Locked Light will not turn off 11085091400 Kenmore Residential dryer

Q:

Kenmore Elite Dryer HE4 Quietpak 9 Model 110.85091400 has 4 dim lights showing on the console display but won't start or respond

A:

I'm real sorry to hear that you are having some difficulties with your Kenmore Elite HE4 Dryer.We all know how fast our clothes can pile up during the holidays. I did some research for you at Managemylife and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices. I hope these links provided assist you.

Read More
James -
December 30, 2011
A:

Thank you Maestro but it is none of the things listed in the link you provided. I do appreciate your response though.

Read More
Eric -
December 30, 2011
A:

I believe the chart in the image below will help you with this problem.

To check voltage from the control to the interface will require the unit be plugged in. Use extreme caution doing this and only if you are confident in you meter skills.

First unplug the dryer while access the control board. Next you can unplug the P3 and P4 connectors. There are two separate test you can now preform.

You can check the interface for continuity when a keypad is pressed. To check the Start keypad place your meter leads on the p4-2 connector and P3-14 connector. When the Start button is pressed you should show continuity. Check any other keypad the same way while using the particular leads for that switch.

To check for voltage to the interface you will leave the ribbon disconnected and check the pins for voltage. Use caution doing this. Put the negative meter lead on the P4-2 connector for neutral. P4 is the smaller connectior to the control board. With the other lead check each of the other pins for 1-2 VDC. If you get this voltage then the lights on the display should be brighter and the interface is likely bad. If you get no voltage then the control is likely the problem.

Be careful and reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
December 30, 2011
A:

It seems that the bottons I have tested so far on the front console are working fine. The continuity changes from 1 to about .6 when you push the button. I have not tested them all yet though. However it is a different story on the main control board. I can not get and voltage readings at all off any of the P3 pins when holding the (-) multimeter probe on P4-2. Am I correct in thinking the main board is probably the culprit here? One thing to note, I unplugged the dryer last night and just plugged it back in to start these diagnostics and I was able to enter the diagnostic mode and all the lights came on and the display read 88. I did not try and start the dryer however because I wanted to keep it able to go into diagnostic if I needed to and I did not want it to disable itself by trying to start the dryer. It definitely seems to be something intermittent though.

Read More
Eric -
December 30, 2011
A:

Sorry for the delay. Checking the DC voltage can be difficult. Sometimes the meter leads can be difficult to get a good reading but if everything lit up and you got 88 then the voltage to the display is most likely okay. P4-2 is not the only neutral. Can you select all the cycles and options. If you can then the dryer not running is the main problem. Intermittent problem are most likely caused by bad connections or even a broken harness. Holidays are over so you'll get a quicker relay so let me know where you're at now and we'll go from there.

Read More
Fred M -
Sears Technician
January 03, 2012
A:

We have ordered the main control board and are waiting for it's arrival. Since I could not get any reading what-so-ever off the pins on that board I figured we would start there. The multimeter is brand new and not one of the cheapies so I have confidence in that. In the instance of the front console working we could select all the options and we were even able to dry a load of clothes... Whoo Hoo!!! But then alas it returned to its inoperable state right after that. The new main board was supposed to be here yesterday bit didn't show so maybe today???

Read More
Eric -
January 03, 2012
A:

Good luck.

Read More
Fred M -
Sears Technician
January 04, 2012
A:

Thanks. We are STILL waiting for the board. I will keep you posted.

Read More
Eric -
January 04, 2012
A:

Fingers crossed.

Read More
Fred M -
Sears Technician
January 05, 2012
A:

Well te board finally got here and bingo... Plugged it in and everything works. I have reserved judgement for a couple of days just to make sure and after 10-12 loads of laundry no issues so I think we are good to go. Thank you for the input.

Read More
Eric -
January 08, 2012
See more answers

Top Parts