Model #11084836200 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Door
    3 Results
  • Pedestal
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Instal dryer handel 11084836200

A:

Thank you for contacting SearsPartsDirect.com with your question about your Kenmore Dryer. I am so sorry to hear the handle needs to be replaced. I will be happy to help you with this. 

The door is held together by screws only. There is not a seal or adhesive that needs to be replaced when installing the new door handle. You will want to remove the door from the dryer to make this repair easier. Make sure you put the door on a towel or blanket while you are working on it to prevent scratching the paint or window. 

When you are reassembling the door, do not tighten the screws individually. It is better if you tighten each screw part way and work around the door edge. This will make it easier to keep the parts lined up and also keep you from overtightening one side and damaging a part. 

I hope this helps. If you need further assistance, please resubmit your question with additional details. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
April 02, 2014
Q:

Electric Dryer no heat 11084836200

A:

I know it can be irritating when the dryer stops working. The information you have already received is correct. I recommend first checking for a tripped breaker, especially if there have been problems, with the power supply. There is a thermal fuse inside this dryer but if it blows, the dryer won't run at all. If the breakers are ok, then the voltage will need to be checked at the dryer terminal block, located behind the unit. Making voltage checks can be dangerous and unless you are very confident in your repair skills and have a meter, a technician will be needed. I'm listing a site you can access, to have a tech come out. Here is a link for the website:

Sears Home Services

I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

Read More
Desirea -
Sears Technician
March 21, 2014
Q:

How do I run diagnostic program on 11084836200 model?

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner. Have a great day!

Read More
Alina -
January 12, 2013
A:

Thank you for your question and I understand your concern.

The dryer can only display 3 fault codes and it should display at some point when it is running or when attempting to start it. It can display PF, E1 or E2.

ACTIVATING THE DIAGNOSTIC TEST MODE;

  1. Be sure the dryer is in Standby Mode (plugged in and all indicators off).
  2. Press the following button sequence: MORE TIME ? LESS TIME ? MORE TIME ? LESS TIME - all within 5 seconds.
  3. All indicators on the console are illuminated with "88" showing in the "ESTIMATED TIME REMAINING" (two-digit) display, if this test mode has been entered successfully.

See image below.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
January 14, 2013
A:

Mike: I added a larger image below. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
January 14, 2013
A:

Hi Joey, Thanks for that info. Hmmm, I thought there was more to it. All checked out, but no error codes. The only code I could make it cough up was going thru the sequence like you said to the "88" display and I pushed "start" and got a "06" code. No other code would come up. I'm guessing it's the thermal relay, or what the Sears operator said - the board, which is shot. Problem is, I ran 4-loads of clothes the day before. Then the next day tried to run another load. I picked my time, pushed "start" and got 1-beep and nothing. The usual lights all light up, but no go with the drum. Dead silence. I did some reading on the net and the most repeated answers to what the problem could be was the door-lock mechanism, the door itself mis-aligned, the thermal temperature fuse, one other fuse and the board. It's been called in for service, so I guess we'll find out what it is when the tech rips into it. Thanks for your insight and the answer I have been digging for. Mike

Read More
Mike -
January 14, 2013
See more answers

Top Parts