Model #11083372110 KENMORE Residential Washers

  • Top And Console
    3 Results
  • Drive Parts
    3 Results
  • Water Pump Parts
    3 Results
  • Tub And Basket Parts (non-suds Only)
    3 Results
  • Tub And Basket Parts (suds Only)
    3 Results
  • Water System Parts (suds Only)
    3 Results
  • Cabinet Parts
    3 Results
  • Miscellaneous Parts
    3 Results
  • Water System Parts (non-suds Only)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Replacing part # 285144 on clothes washer Kenmore Mod # 110.83372110 ( 1985 vintage ). How do you re-install the new vlave body to the existing solenoid?

A:

It is always important to properly fix your vintage appliance. I have found a great link that I believe has some great tips for you while you wait on your response from an expert. I attached the link below if you are interested in viewing. Have a great day!

Read More
Alina F. -
May 04, 2012
A:

Thank you for your question and I understand your concern.

The solenoid is held in place with pins so it can pivot a little. See image below and it shows the upper and lower mounting brackets with 2 holes at the bottom and one at the top where it connects to the arm. Align the solenoid up with the holes and slide the pins through and slide the push nuts over the end of the pins to keep the pins from sliding out.

I added an image below that may help. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 05, 2012
A:

Joey: VERY helpful and thank you! Concerning the 2-way valve, I had worked the valve in/out by hand ( moved freely under some tension ). When we did this and ran a load of laundry, the water saver feature worked on the first time. After the second attempt after another load of wash, it no longer would take water out of the laundry tub back into the washer. I had also watched the solenoid activate whenever we activated the �suds saver� controller so I figured the problem has to be with the 2-way valve. The pump works fine as it removes water from the washer very quickly and under force. Are we on the right track of replacing the 2-way valve?

Read More
Anonymous -
May 07, 2012
A:

Anonymous: I was under the impression that you had replaced the two way valve. If you haven't then it will likely need to be replaced.

Read More
Joey S -
Sears Technician
May 07, 2012
A:

We had ordered the 2-way valve last week ( part # 285144 ) from Sears Parts Direct so we needed to know how to install once it arrives.

Read More
gary -
May 07, 2012
A:

Gary: Okay, now I understand, you haven't replaced the two way valve and your waiting for it. Replacing the two way valve should resolve the problem.

Read More
Joey S -
Sears Technician
May 07, 2012
A:

Joey: We replaced the 2-way valve yesterday. Today, we tried the washer on suds saver mode following a normal wash. The suds saver did not work ( would not draw water back out of the laundry tub to the washer ). We had verified the solenoid is activating as we could see it energize when we would depress the �suds� button on the washer panel ( suds saver ). Is it possible the pump is not activating only when in the suds saver mode? It DOES pump water out of the washer during normal washings so the pump does work. If the problem is not the 2-way valve or the solenoid, what else could we check? And, how & where would we check? Pls keep in mind I am not an electrical guy! THX!

Read More
gary -
May 14, 2012
A:

Gary: I must assume you have the drain suds saver hose hanging into a sink in order for it pull the soapy water back into the washer. I added an image below showing how the suds saver operation works. You could have a faulty self cleaning filter located on the side of the tub preventing it to pull water back into the tub.

Read More
Joey S -
Sears Technician
May 14, 2012
A:

Joey: Thanks! We do have a hose hanging in the tub. There is a plastic ( what I call a wedge ) to filter out major lint etc. It has never plugged; in fact, when water discharges into the tub, it does so in a strong fashion. The only other filter is that which is attached to the drain hose& routs directly to the drain, not the tub. It too is kept clean. We do notice when we activate the suds saver when water is in the utility tub, a belch of air occurs but no water is drawn back into the washer from the utility tub. We�re corn-fused!

Read More
gary -
May 14, 2012
A:

Gary: Look at the image I added in the last post and you will see how the suds water is drawn out of the sink and back into the washer. It will only draw the suds water back into the washer after it initially drains the first time after the first agitation cycle. Gary I suggest calling a service technician to diagnose and repair your washer if you do not feel confident repairing this problem yourself. You can have it repaired at your home by a Sears technician. Here is a link for the website: [Sears Home Services | http://www.searshomeservices.com?sid=MMLxexpertxmerch] .

Read More
Joey S -
Sears Technician
May 14, 2012
See more answers
Q:

Kenmore Clothes Washer Repair Manual-Model # 110.83372110?

A:

ManageMyLife.com is a great place to find manuals for various products. I understand you are having some difficulties finding a repair manual. On searspartsdirect.com you can find a parts list which may be helpful. If you are having a specific problem please submit your question on the existing tread by click on the reply box below for your expert. An expert will be with you shortly if we can find a repair manual. Thanks for your patience.

Read More
Anna T -
May 07, 2012
A:

Here is a link for an online technical study course on the water system for that type of washer: Washer Study Course -- Water Systems .

I did not find a repair manual for that specific model of washer. The above manual may help you. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
May 09, 2012
A:

Lyle: Thx. Never have seen this before...........

Read More
gary -
May 09, 2012
See more answers
Q:

My son was given a Kenmore series 70 washer by his boss. No manual or drain hoses came with it. It is a "suds" model. How do I hook up drain hoses?

A:

When replacing a major part on your washer, Manage My Life is here to help. While you are waiting for your expert answer, I did manage to find a link that will provide you with some good information to help you with your question. I hope my link is useful.

Read More
Joseph P. -
July 07, 2011
A:

Lift up the lid of the washer. The model number should be in the form of yyy.yyyyyyy. Go to the Manuals section of this website & plug the model number in for the manual -print it if you want to.

Read More
LookOver1 -
July 07, 2011
A:

Sorry, that doesnt help. have the model number as 110.83372110. and nothing shows up in the search. It is a "suds" model that has a type of water recycling system with 4 drain ports on the back. I would like to see a diagram of how these should be hooked up.

Read More
Anonymous -
July 08, 2011
A:

Thank you for your question and I understand your concern.

I added an image below showing where to connect the drain hoses. The longer drain hose as shown in the image below would drain into a sink basin. The shorter one will connect to the stand pipe/drain pipe.

Read More
Joey S -
Sears Technician
July 09, 2011
See more answers

Top Parts