Model #11082983810 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Console Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness Parts
    3 Results
  • Water System
    3 Results
  • Gearcase
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What do I need to do to change the worn dogs inside the agitator of my Kenmore washer model 110.82983810?

A:



You should remove the plastic cap on the top of the agitator. Remove the bolt inside the agitator. If you have removed the bolt, there is nothing holding the agitator. Grasp the upper portion of the agitator and lift up. You might have to jerk sharply to break it loose.

Read More
expert -
Sears Technician
February 18, 2008
A:

I have removed the entire agitator without difficulty but cannot remove the top section to remove the worn dogs

Read More
Gary -
July 07, 2014
See more answers
Q:

how do I replace the switch to make my washer spin.

A:

Thank you for your question.

By what you have stated, it sounds like a lid switch failure. The lid switch has to be closed for the drain and spin cycle on your washer to work. If the lid switch is faulty, it will fill and wash but nothing else. A quick check you can do is to jump the lid switch and see if it will drain. If the washer operates, the lid switch needs to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the two colored wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. Start the washer in a drain cycle. If the washer drains and spins, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

Please click here to watch a video on how to replace the lid switch.

I hope this is helpful. Please reply below if you need further assistance. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
October 27, 2011
Q:

Why does my washing machine take so long to fill with water?

A:

Something like this is caused by a blocked fill line or faulty water valve. I recommend checking the water supply & fill valve screens. Water valve; 285805, hose 76314 X’s2.www.searspartsdirect.com

To check for clogged screens: Turn off water and remove the inlet hoses from washer. Remove any accumulated film or particles from the water inlet screen. Make sure rubber washers are in the end of each inlet hose. Reinstall hoses making sure there are no kinks in the hoses then turn on water and check for leaks. For more information,

see: How to clean the Fill Valve Inlet Screens

Read More
biker dave -
Sears Technician
April 10, 2010

Top Parts