Model #11082980830 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Gearcase
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Capacity for this model please? 11082980830 Kenmore Automatic washer

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.

I do apologize due to the age of the product we no longer have th cubic feet of your washer. You would need to measure the unit in order to get the cubic feet.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 


 

Read More
Natasha12 -
Sears Technician
August 03, 2015
Q:

No spin, no drain 110.82980830

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your washer and I do understand your frustration. Glad to help out. I'm looking at your model number 11082980830 and based on the symptoms you are having I would suspect the problem it the timer. If the timer does not pause the motor before it closes the contact to reverse the motor it could cause the motor to smoke. When you lift the lid or push in on the timer, it allows the motor to pause and change directions. Without making any checks I recommend replacing the timer. Here is a video  that will help with the repair. I have included a link to our Parts Direct page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
October 16, 2014
Q:

Washer 110.82980830 Water inlet valve installation 285805

A:

I think its great that you are wanting to do some repairs on your own. I am adding a link below to help you with your question while you wait for your expert response.

Read More
Joseph P. -
February 11, 2012
A:

Thanks; I had already viewed that (and many other posts) prior to adding a conversation. Since Searspartsdirect was not helpful, I am hoping an expert can provide the info I need.

Read More
C -
February 11, 2012
A:

After getting an extra hole drilled in the mounting plate, I finished installing the water inlet valve. Now I get absolutely no cold water, no matter the temperature setting. Before replacing it, I got a trickle of cold water on Cold/Cold (not in Elec/tronic Temp Control; that was a rush of very warm water). I've verified that there is cold water coming up to the washer (hoses,filters etc). I tried switching the wires from hot solenoid to cold, cold to hot. The result was hot water on all settings except Hot/Warm and Hot/Cold. I switched that wires back, and the result was hot water on all settings except Cold/Cold (Electronic Temp setting) and Cold/Cold (non-electronic). Any suggestions for next step? It's hard to afford a service call these days ... Thanks.

Read More
C -
February 11, 2012
A:

Here's my last tidbit. After searching other posts, I checked whether the water came in to the washer any differently on a rinse cycle. No difference from the above post, whether the wash cycle is at the beginning fill or a rinse fill. That is, any setting with Cold in the rinse setting = no water flow

Read More
C -
February 11, 2012
A:

I'm sorry you had such a bad experience and I wish I could have gotten to this question quicker. We may be slower but you'll get answers and no sarcasm.

The image below is what you should have. This is a substitution and you should have a bracket with multiple holes so it can fit different washers. The part number you should have is 285805.

The valve should work. The valve should attach without the bracket. Check out the following link to a video and see if it helps you complete this project: Changing valve .

I hope this helps.

You can reply with any additional details or questions for further assistance. The reply skips ahead in the line so you usually get a quicker response. Good Luck with this project.

Read More
Fred M -
Sears Technician
February 12, 2012
A:

Thank you Fred; I have completed installation of the water valve, but it did require drilling an extra hole in the mounting plate. Please read my other posts; I still do not have cold water flow and believe there is a different issue, such as a switch or a timer. Thanks.

Read More
C -
February 12, 2012
A:

I suspect the problem is the 3955728 ETC control. (Electronic Temperature Control) If you wish to check this the let the washer run a final spin cycle. During the first two minutes of spin you should get a spray rinse for 2-3 seconds. If you get this then the valve is okay.

Read More
Fred M -
Sears Technician
February 13, 2012
A:

I followed your instructions and there was water for a few seconds, twice during a spin cycle (still only hot). I looked up the part number and it's for a "microcomputer" - I don't see this part on the schematics for my washer. Is this something I could install myself? Could you send instructions? Thanks for the direction.

Read More
C -
February 13, 2012
A:

The spray rinse should have been cold. Be sure the hoses aren't reversed. The microcomputer is the Electronic Temperature Control I mentioned in an earlier post. It is located in the console area. The console can be raised by removing the two screws on the corners. See the image below for help with this. Remember to unplug the washer first. The water in the spray rinse should have been cold.

Read More
Fred M -
Sears Technician
February 15, 2012
A:

Same happened to me, except i have no HOT water flowing. i have checked hose and screen filter. Water is flowing to washer in rear, but no water flowing into washer in any cycle

Read More
charles -
April 02, 2013
See more answers

Top Parts