Model #11082980820 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Console Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Gearcase
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Automatic Washer rough cycle transitions 110.82980820

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your washer. Upon researching model110.82980820;it sounds like the timer may need to be replaced. The timer controls the cycles of the unit so when it begins to fail the cycle can get stuck or become out of their normal order. I have posted a link of the timer to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
July 19, 2015
Q:

spin cycle 11082980820

A:

Having your washer malfunction and not go into the spin cycle can be extremely frustrating. I did some research and provided a link to a similar question and answer on our site. I hope this will give you a better idea on the next step to take until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
December 07, 2012
A:

I may need a few additional details to help you with this problem. If the washer will agitate then the motor is likely okay. If the water drains out then the motor is reversing and the timer is likely okay. If the water drains out and the machine tries to spin but won't I suspect the clutch and/or basket drive is likely the problem. Can you turn the basket by hand? Please reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
December 09, 2012
A:

Hi Fred I have a model A613 maytag washer and I changed the beltsadjusted the punp for the proper tension but im still haveeing a problem with it spinning it wants to start and spin but than stops and makes aload humming noise and now the mator was starting to smoke a tad

Read More
Harley Tackett -
December 09, 2012
A:

One thing to try first is to remove the belts from the motor and pump and see if the motor will run okay with the belt off. The brake or bearing can seize causing the motor to burn the belt. This may be the smoke you see and smell. If the motor still starts and shuts down then the problem is likely with the timer or motor. From the description you give the motor is working in the agitation cycle so it is most likely okay. Try removing the belts and let me know if the motor runs okay.

Read More
Fred M -
Sears Technician
December 10, 2012
See more answers
Q:

What is wrong with my Kenmore model 110.82980820 washer when it will not spin without going out of balance unless it is empty?

A:

The tub wobbling may be the key to this problem but there are some other things to consider as well. The tub has a spanner nut that holds the spin basket to the drive tube. If the basket has excessive (1 inch) movement up and down and "wobbles" then the spanner nut may be loose. You can check this by removing the agitator. The first image may help with this. If the nut is loose then tightening it may help. There is a special tool for this. It is called a spanner wrench part number TB123 out of division 92 source 150 and can be obtained from the following link: SearsParts Direct . You can also view a complete parts breakdown for you particular washer if you enter the model number. Any part you need to repair the washer can be ordered at the site.

Another possible cause of the out of balance in all loads is a broken suspension spring and/or counter weight spring. This can be checked by removing the cabinet. The 2nd image will show you how to do this. There are three suspension springs and one counterweight spring. Remember to unplug the washer first.

Tightening the spanner nut or replacing the suspension springs are things that can be done as a do-it-yourself project. Similar new washers cost approximately $500 dollars so I wouldn't recommend a major overhaul. The basket stopping immediately can indicate a problem with the clutch/basket drive but that would cause the primary problem of the out of balanced loads.

I hope this information helps to resolve this problem but make some checks and submit another question with any additional details for further assistance.

Read More
Fred M -
Sears Technician
December 03, 2009

Top Parts