Model #11082834100 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Door
    3 Results
  • Pedestal
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

How do I replace the door handle on my Kenmore HE3 Dryer?

A:

You will need a T-20 torx driver to remove the screws securing the outer panel to the inner panel. Remove only the screws that the yellow flags are pointing at. (See image below) Separate the outer door panel from the inner door panel to access the door handle mounting screws.

Read More
Joey S -
Sears Technician
May 08, 2009
A:

Thanks joey that was a breez, took about ten minutes, thanks for the easy step by step instruction, can't wait for my next project to call again randy

Read More
randy bumgarner -
January 25, 2011
A:

would you be able to repost the image that shows what screws need to be removed, I do not see the image in this discussion. Than ks

Read More
Eric -
October 07, 2013
A:

Joey - could you please send me or re-post a larger picture showing the yellow arrows? thank you, mark

Read More
mark lidke -
November 08, 2015
A:

Joey - could you please send me or re-post a larger picture showing the yellow arrows? thank you, mark

Read More
mark lidke -
November 08, 2015
A:

I have a model # 247887760 lawnmower and am having an issue as the lawnmower is not be able to be pulled backwards. The rear wheels lock up. What do I need to do to get this fixed. I have already replaced the nylon springs and pawls. The transmission works fine, and it will go forward without any issues, it is just not able to be pulled backwards with out having to be lifted up as the wheels lock up.

Read More
Mike -
November 08, 2015
See more answers
Q:

With regard to our Kenmore Elite HE3 dryer, the dryer is not starting when the dryer button is pushed. The model # is: 11082834100; 1E shows in the display

A:

Error codes are like a puzzle they can be hard to solve. While you are waiting on an expert to answer your question, I found a great link that can help you. I have attached the link below. Hope this helps!

Read More
Dezeray S -
August 22, 2011
A:

Thank you for your question and I understand your concern.

The "E1" fault code means the thermistor is open or an open thermistor circuit. Replace the thermistor and your dryer will likely operate again. The thermistor is part #8577274 and can be ordered from Sears PartsDirect .

I added an image below with the instructions for accessing and replacing the thermistor. NOTE: Disconnect the power cord from the power source before removing the lower front access panel.

This may be the issue. If not, please reply and I will be glad to assist you further.

Read More
Joey S -
Sears Technician
August 24, 2011
See more answers
Q:

how to replace thermistor on dryer

A:

Hi Carol, Replacing parts on any appliance can be simple or hard. What may be helpful is to consult the manual for the dryer first. If you have the model number handy, you can enter it at the manuals tab at this site. If you need schematics, you can also enter the model number at Sears Parts Direct. I attached the links below. If down the road you feel this is the hard type you can visit SearsHomeServices to schedule an expert repair technician.

Read More
Barbara H. -
June 27, 2010
A:

This is a model specific procedure. Replacing the thermistor usually involves removing panels and disconnecting a single two wire connection to replace. Please submit a model number for more specific instructions.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Travis R -
Sears Technician
June 29, 2010
A:

I need specific instructions for replacing the exhaust thermistor in our Kenmore Elite HE3 dryer, model #11082834100; serial #MM4205019. This unit was purchased in 2002. When I called the ManageMyLife 800#, asking for the meaning of the diagnostic code 1E or IE, she indicated the problem was the exhaust thermistor. We hope to purchase the part and replace it ourselves. She indicated it is fairly simple and straight-forward. Please give step by step instructions. Thank you! In addition, could you verify that the suggested solution of replacing the exhaust thermistor is in fact the solution to the diagnostic code given? Many thanks!

Read More
Anonymous -
August 19, 2011
See more answers

Top Parts