Model #11082781800 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Console Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Gearcase
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Why does my washer fill with warm water when I pick cold wash cold rinse? 11082781800 Kenmore Automatic washer

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore washer.

From the information you have provided above, I can understand the frustration of having your washer malfunction, after researching model number 110.82781800. The cold bi-metal thermostat on the fill valve assembly should be closing to energize the hot water valve during the warm fill. You could have a bad bi-metal thermostat on the fill valve assembly. You could also have a bad switch temperature causing this problem.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting www.SearsHomeService.com*

Read More
Benny23 -
Sears Technician
June 13, 2015
Q:

leaking water 11082781800 Kenmore Automatic washer

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

 I am sorry and do understand your frustration when there are leaks in the washer area.

Glad to help out.   Im  looking at your Kenmore model number 110.82781800.

What I advise people to do as myself.   Dry the floor well and then put a news paper underneat the washer.   Run it through a cycle and see if the water leak is more in the back or the middle.   If it is in the back then you need to check  you water inlet hoses first.  Unscrew them from the valve and check for deposits on the screens inside the hose and the water valve where the hoses screw into.  Check both the hot and cold water hoses.  If the screens are clear then check the drain hose.  Make sure it isn't kinked or blocked.   Check also the pipe that the drain hose, drains into please to make sure it is clear.

2.  If the water is from the middle of the newspaper then you are having water leak where the pump is and need to look to see if you have a clogged line or pump.

water inlet per model 110.82781800

water pump per model 110.82781800

 If you have further questions please let me know.

Thanks for choosing Sears PartsDirect.com

 

Read More
Larry L -
Sears Technician
October 30, 2013
Q:

Kenmore Automatic washer 11082781800 won't spin or drain

A:

I understand your concern toward wanting to make sure your washer is working properly so that you can keep clean clothes in your home. While you are waiting for an expert answer, I did mange to find a link that will provide you with more information about your problem. Hope this helps!

Read More
Priscilla V -
July 31, 2012
A:

I know that it can be very frustrating to have issues with your washer. By what you have stated, it does sounds like a lid switch failure. The lid switch has to be closed for the drain and spin cycle on your washer to work. If the lid switch is faulty, it will fill and wash but nothing else. A quick check you can do is to jump the lid switch and see if it will drain. If the washer operates, the lid switch needs to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the gray and tan wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. Start the washer in a drain cycle. If the washer drains and spins, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

Here is a link to order any parts you need. Sears Parts Direct . If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
July 31, 2012
See more answers

Top Parts