Model #11082682110 KENMORE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Console Panel Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Miscellaneous Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Water System Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Will not wash on cold setting 11082682110 Kenmore System 21 automatic washer

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

I am sorry and do understand your frustration when there is trouble with the washing machine.

Model number 110.82682110 that I am looking at.   Saying you are having trouble not getting cold water to do the laundry.   Sounds like you need to buy and install a new water valve for the back of your machine where the hot and cold water hoses hook into.  Speaking of hoses.   It is highly suggested and remind people that you need to change your hot and cold water inlet hoses every 5 years as a safety percaution due to them going bad from the inside out and you can loose up to 500 gallons of water in the space of a half hour if they do break when you are not at home to take care of it quickly.

I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

water mixing valve per model 110.82682110

hot and cold water inlet hoses 

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

 

Read More
Larry L -
Sears Technician
August 12, 2013
Q:

How do you remove the timer from the washer to replace

A:

Hi Grace. I can appreciate your need for proper instruction regarding replacing your washer's timer. I was able to locate a link with instructions for a model that is similar to yours. Click on the link below to view the page. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this information will be helpful and have a nice day.

Read More
Henry -
August 06, 2013
A:

Thank you for choosing ManageMyLife.com. I understand how important it is to be able to repair a broken timer for your washer. I have included instructions below on how to replace your old timer.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Unplug the washer's power cord from the wall outlet.

2. Remove the two plastic end caps on the front left and right sides of the control panel. To remove, lift the top of the end cap and pull toward you.

3. Remove the screw below each end cap to release the control panel. Rotate the control panel up 180 degrees so the internal components are accessible.

4. Locate the two holes on the right side of the rear of the timer unit placed above one another. Locate the hole placed to the immediate left of the two holes.

5. Insert needle-nose pliers into the hole and pull out the long black rod inside the hole.

6. Lift the knob off the front of the timer, then remove the clear plastic piece below the knob and the dial. Simply depress the center clips.

7. Remove the two screws located below the dial on the timer.

8. Unclip the wire harness from the side of the timer from the inside of the control panel.

9. Slide the timer assembly to the left to unclip, then remove the timer assembly.

10. Insert the hooks on the right side of the new timer assembly into the grooves on the inside of the control panel, then slide the timer to the right to lock it into place.

11. Connect the wire harness to the side of the timer.

12. Connect the mounting screws to the front of the timer from the outside of the control panel.

13. Pull the black rod out of the hole on the new timer, if necessary, using the needle-nose pliers.

14. Place the dial and plastic piece back onto the timer post, then snap the timer knob back onto the timer post. Insert the black rod from the rear to secure the timer knob.

15. Rotate the control panel down and secure it with the two screws that were removed from the bottom left and right sides of the control panel.

16. Snap the plastic end-caps back onto the washer.

17. Plug the washer back into the wall or turn on the breaker.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.
Timer for Kenmore Washer Model # 11082682110
If you have further questions please let me know. Thanks for using ManageMyLife.com.

Read More
Lokelani -
Sears Technician
August 07, 2013
See more answers
Q:

Why won't my Kenmore washer deliver hot water on any setting?

A:

The model number is valid. You can view a parts list diagram of the washer on the Sears PartsDirect website. The owner's manual is not available online. The hard copy of the owner's manual is no longer available either.

This hot water fill problem could be caused by a failure of the ETC (Electronic Temperature Control) board or the water fill valve assembly. A failed thermistor (temperature sensor), a bad temperature selector switch or a wiring failure between components could also cause this problem. I recommend calling a service technician to diagnose the washer and determine the exact cause of the failure.

Read More
Lyle W -
Sears Technician
March 23, 2009

Top Parts