Model #11082671110 KENMORE Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Miscellaneous Parts
    3 Results
  • Console Panel Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Water System Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Problems removing lower agitator from kenmore top load washer

A:

I forgot to mention that this is a 25 yr old washer that, aside from needing cleaning, works perfectly. Given the age of the washer, it may be that the the lower agitator is simply stuck to the motor spindle. If this is the problem, what I am looking for is a trick for puling the agitator off the spindle.

Read More
david1997 -
October 07, 2013
A:

  Thank you for your question.  You removed the upper part of the agitator and you say you removed the 7/16 inch bolt so the lower part of the agitator should come straight up.  The problem is that over time gunk can build up and act like adhesive.  If the machine will fill and drain then you can try filling the tub with hot water and let it soak awhile then drain the tub and try to remove the agitator.  I hope this helps.  You can reply below with any additional details for further assistance.   Thank you for using Manage My Life. 

Read More
Fred M -
Sears Technician
October 08, 2013
A:

Dear Fred, thank you very much for your suggestion. I will try this. Just so I am sure I understand the idea, are you expecting the heat to loosen the gunk, and/or expand the spindle and surrounding plastic in the agitator? I read here (http://www.engineeringtoolbox.com/linear-expansion-coefficients-d_95.html) that plastic expands with increased temp more than metal. So this would be perfect for loosening up these parts, given that the plastic is outside and the spindle (metal) is inside. Are there any tricks for pulling up hard on the agitator? I exhausted my fingers (and my back) tugging at the agitator. I was thinking about lightly tapping in some wedges at the bottom. If I get the agitator out, my plan is to use one of those special spanner wrenches to free up the nut that secures the metal basin, and am hoping that I will then be able to remove the plastic tub for cleaning (although I could do it in place). Note this all started with a washer leak, which I traced to a leaking drain pump, which is easy to replace. But when I saw the grim that had accumulated over the last 25 yrs, it seemed like a good time for a thorough cleaning. It's really great to be able to get help from a community of experts!

Read More
david1997 -
October 08, 2013
See more answers
Q:

Inlet water won't fill tub

A:

A Kenmore washer is an appliance that we depend on just about everyday and when it doesn't function properly it can be frustrating. I am providing a link on a similar issue with a washer. Hope this is helpful while waiting for an expert response.

Read More
Anna T -
October 19, 2012
A:

Thanks for contacting ManageMyLife.com. I understand how frustrating it is having trouble with your washer not filling with water properly. We are here to help. I suspect the timer is bad. However, before you purchase that part, you need to separate the cabinet from the back of the washer. Next, Turn the timer to the wash cycle and turn it on. Now measure the voltage to the mixing valve with a multimeter. If the voltage is zero, check the water level switch. Both parts having zero voltage would confirm a bad timer. The part number for the timer is 661549. This part number includes the timer motor. I provided you a link below to order the part. The image below will help you separate the cabinet from the back of the washer. I hope this helps.

To purchase the timer, please visit SearsPartsDirect.com .

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Read More
John H -
Sears Technician
October 20, 2012
See more answers
Q:

What year was my washer built? Kenmore c73444960

A:

Hello, I see you would like to know what year your Kenmore Washer was built in, which is a great question. To find your answer more efficient you can visit our Sears.com website and get in contact with a customer representative who can give you exact dates. I attached the link below. Hope this helps!!!!

Read More
Raquel F -
July 16, 2010
A:

I have checked the serial number that you have submitted and your washer was manufactured 8-20-1987. If you need further assistance, please submit more information.

Read More
Mark T -
Sears Technician
July 19, 2010
See more answers

Top Parts