Model #11082407130 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Console Panel
    3 Results
  • Meter Case
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Gearcase
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

commercial kenmore washer

A:

Knowing the cubic feet of the washer can be very helpful. I did some research on your model number but was not able to find the information. Your expert will be able to help answer your question. It may take 24-48 hours. I do hope everything works out.

Read More
Marc -
November 21, 2012
A:

Hello Debb,

I would like to answer your question for you. The wash capacity of your washer is 3.5 cu-Ft.

Please let me know if you would like any further assistance.

Jerry C

Read More
Jerry C -
Sears Technician
November 24, 2012
See more answers
Q:

Sears kenmore model 110.82407130 washer will not start at all.

A:

The Kenmore washer is an appliance most people use everyday. When not functioning properly its frustrating. The link provided below may be helpful while waiting for additional information from an expert.

Read More
Anna T -
October 02, 2012
A:

Hello Jack,

I would like to assist you with your washer. I have a few questions for you, does the washer hum at all when you attempt to start it? If it does, this may be the inlet hoses plugged. If the washer does not fill, it will not do anything and will just sit there. Any other things that you have noticed will assist in figuring this out. If you are not comfortable making checks or electrical tests, Sears Home Services is a link to arrange a Sears service tech to perform the repair.

Please let me know if you would like any further assistance.

Jerry C

Read More
Jerry C -
Sears Technician
October 03, 2012
See more answers
Q:

What is wrong with a model 110.82407130 Kenmore washer that pumps and spins at the same timer and water is thrown out.

A:

From the description of the problem the most likely cause of this is a bad transmission.

Kenmore washers have what is called a "neutral drain" and initially the washer would drain the water out but not spin. After a minute or so the timer will pause for just a moment and the transmission comes out of neutral drain and start to spin.

Sometimes the failure occurs as a timer fault. If the timer is at fault the washer will drain and continue to drain but not start the spin cycle till the timer is turned off or the lid is open for a moment. If the timer doesn't pause the washer will continue to drain and not come out of the neutral drain to spin.

Let the washer agitate for a few minutes to set the neutral drain and try it again. If the washer starts to drain and spin at the same time the transmission will have to be replaced.

You don't mention how old this washer is but the transmission generally had a 5 year parts warranty.

You can submit another question with any additional details for further assistance with this problem.

Read More
Fred M -
Sears Technician
October 13, 2009
A:

From other machines I have observed, the washer goes immediately from agitate to drain. This machine has a 30 second pause between agitate and drain. This pause, I believe is allowing the tramsmission to unlock. There is a second pause after the machine spins and pumps for about 1 minute.

Read More
Larry -
June 19, 2012
A:

Fred i have a question for you. i have the exact same washer as the guy above with a different problem. the washer wont start at all, there is power running to it and water also, it turns on but it just will not start at all, no water no spinning not anything. sorry if it is vague but I'm describing to the best of my abilities if you could get back to me i sure would appreciate it.

Read More
Jack -
October 02, 2012
See more answers

Top Parts