Model #11082382110 KENMORE Residential Washers

  • Top And Console Parts
    3 Results
  • Drive Parts
    3 Results
  • Water Pump Parts
    3 Results
  • Tub And Basket Parts (non-suds Only)
    3 Results
  • Tub And Basket Parts (suds Only)
    3 Results
  • Water System Parts (suds Only)
    3 Results
  • Cabinet Parts
    3 Results
  • Miscellaneous Parts
    3 Results
  • Water System Parts (non-suds Only)
    3 Results
  • Gearcase Parts
    3 Results
  • Basket Drive And Brake Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore washer series 80 model # 110.82382110 won't SPIN.

A:

The problem with the washer is concerning. I found some information for you that I am really hoping will help you with the washer until your expert answers your question. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you out.

Read More
Marc -
November 04, 2012
A:

The problem with the washer is concerning. I found some information for you that I am really hoping will help you with the washer until your expert answers your question. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you out.

Read More
Marc -
November 04, 2012
A:

Sorry for the double post.

Read More
Marc -
November 04, 2012
A:

I know that it can be very difficult to have issues with your washer. From your description this issue is most likely being caused by a bad lid switch. The lid switch has to be closed for the washer to drain. If the lid switch is faulty, the washer will fill and agitate but then nothing else. A quick check you can do is to run a cycle with the lid switch bypassed. If the washer operates, the lid switch needs to be replaced. To bypass the lid switch you need to unplug the washer and open the console. Here is a video that demonstrates gaining access to the lid switch: 80 Series Lid Switch .

Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the outside wires (see image below), not the green it is a ground and will cause a short. The red arrows indicate where you need to place the bypass and the green arrows indicate where the lid switch is connected in the washer. After inserting the jumper, make sure it will not touch anything metal. I recommend covering it with electrical tape. After ensuring that the lid switch bypass is secure, plug the washer in. Then start the washer in a cycle, and let it go. If the washer completes the cycle, you need to replace the lid switch. Do not leave the jumper in place and continue using the washer while you are waiting for the part. The jumper is for testing purposes only. If you do not feel comfortable doing this yourself, just click on this link to schedule service: Sears Home Services . If you are going to replace the part, you can order it from this link: Sears Parts Direct . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
November 05, 2012
See more answers
Q:

Kenmore washer series 80 model # 110.82382110 won't drain.

A:

The problem with the washer is concerning. I found some information for you that I am really hoping will help you with the washer until your expert answers your question. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you out.

Read More
Marc -
November 04, 2012
A:

I know that it can be very difficult to have issues with your washer. From your description this issue is most likely being caused by a bad lid switch. The lid switch has to be closed for the washer to drain. If the lid switch is faulty, the washer will fill and agitate but then nothing else. A quick check you can do is to run a cycle with the lid switch bypassed. If the washer operates, the lid switch needs to be replaced. To bypass the lid switch you need to unplug the washer and open the console. Here is a video that demonstrates gaining access to the lid switch: 80 Series Lid Switch .

Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the outside wires (see image below), not the green it is a ground and will cause a short. The red arrows indicate where you need to place the bypass and the green arrows indicate where the lid switch is connected in the washer. After inserting the jumper, make sure it will not touch anything metal. I recommend covering it with electrical tape. After ensuring that the lid switch bypass is secure, plug the washer in. Then start the washer in a cycle, and let it go. If the washer completes the cycle, you need to replace the lid switch. Do not leave the jumper in place and continue using the washer while you are waiting for the part. The jumper is for testing purposes only. If you do not feel comfortable doing this yourself, just click on this link to schedule service: Sears Home Services . If you are going to replace the part, you can order it from this link: Sears Parts Direct . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
November 05, 2012
See more answers

Top Parts