Model #11078702895 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • 3402844 Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

lint dust every where 11078702895 Kenmore Gas dryer

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
May 13, 2014
Q:

11078702895 drive belt issues how do i install properly --washer parts for dryer whrere does it go

A:

Having the washer up and running ready to work is very important. Installing the belt can be a task. I found some information for you that I am hoping will help you replace the belt. I am adding the link below to help you with your question while you wait for your expert response. I do hope that this will help you with the dryer.

Read More
Marc H -
June 18, 2012
A:

Thank you for your question and I understand your concern.

I added a video with the procedure of installing the drum belt. The drum belt #341241 for Kenmore dryer model 110.78702895 can be ordered from Sears Parts Direct.

Click here to watch the procedure of replacing the drum belt. I also added an image below of the how the belt is routed under the belt tensioner and motor pulley. NOTE: Disconnect the power cord from the power source before servicing your dryer.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
June 19, 2012
See more answers
Q:

Why is my Kenmore gas dryer not heating up?

A:

Make sure that the gas supply cut-off valve for the dryer is fully open and that you have a proper gas supply provided to the dryer.

You can observe the burner assembly through the hole in the front panel to see if the igniter is glowing on the burner assembly with the motor running and the dryer set to a heated cycle. If the igniter is not glowing, then I recommend checking the thermal fuse. Unplug the dryer and remove the back panel. The thermal fuse is on the blower housing as shown in the first image below. (An electric dryer is shown in this image but the thermal fuse is in the same location.)

To check this fuse (with the dryer still unplugged), pull one wire off and measure the resistance across the leads of the fuse with a volt/ohm meter. You should measure near zero ohms of resistance (closed). If you measure infinite resistance (open), then the fuse is blown and will need to be replaced. You can verify that this is the only failure that is preventing the dryer from heating by taping the wires that go to the thermal fuse together with electrical tape to temporarily bypass it and test the dryer. If the dryer heats with this fuse bypassed, then you have verified that the blown thermal fuse is the only component failure that is preventing the dryer from running. NOTE: Do not leave this fuse bypassed and continue to run the dryer. This fuse must be replaced. It is an important safety feature of the dryer. Also, if the thermal fuse was blown, check for an exhaust vent duct restriction that could have caused this fuse to blow. Check the flexible vent behind the dryer for a kink or clog. Check the exhaust vent duct system to the outside of the home for a restriction. Failure to correct this type of problem could cause the thermal fuse to blow again.

If the thermal fuse is okay, then you can check the operating thermostat and the high limit thermostat in the same manner as the thermal fuse. If both of these components are okay, then you could have a failed igniter, an open flame sensor, a failed motor centrifugal switch, a bad timer switch, failed gas valve coils or a wiring failure between components in the heating circuit.

If the igniter does glow and then cycles off, then you likely have failed gas valve coils. If the igniter glows and never cycles off to allow current to flow through the gas valve coils to open the gas valves, then you likely have a failed flame sensor on the burner assembly.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
April 10, 2009
A:

OK I BYPASSED THE FUSE AND TAPED THE WIRES TOGETHER.I OPENED THE PEEPHOLE IN THE FRONT AND TURNED THE DRYER ON. ISAW THE GLOW PLUG LITE UP AND THEN THE GAS IGNITED AND THE DRYER GOT HOT,THERMAL FUSE RIGHT? SOI BOUGHT A THERMA FUSE AND INSTALLED IT ,REMOVED THE THE PEEPHLE COVER AND TURNED THE DRYER ON.THE GLOW PLUG LIT UP BUT THE GAS DIDN'T IGNITE.SO THEN THE GLOW PLUG WENT OFF AND THE DRYER STILL DOESN'T GET HOT.PLEASE HELP. KENMORE MOD 3 110.74852.400

Read More
anthony -
March 15, 2011
See more answers

Top Parts