Model #11077950110 SEARS Laundry Appliances Division (26)

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

I have a kenmore gas dryer 110.77950110 and i need to replace the drive belt how can i figure out how to go about this.

A:

Detailed instructions can really come in handy when replacing a major part on your dryer and I will be happy to help. I did some research and I was able to find a link that will guide you with your project. Click here for the link. I hope this helps with your research while you wait for your expert response.

Read More
Joseph P. -
July 11, 2013
A:

Thank you for your question and I understand your concern.

In order to replace the belt, disconnect the power cord from the power source.

Remove the two screws from under the lint screen. There is a retainer clip the top snaps down and locks on to the top near each corner. Use a putty knife to slip between the top and the upper front panel and push inwards and at the same time lift that corner of the top up a little. Repeat step for the other side. Hinge the top open and let it gently rest up against the wall. You now need to remove the two screws securing the front panel to the left and right side panels. There will be two more at the bottom of the front panel too. Disconnect the door switch connections and remove the front panel but you will need to hold the drum in place. Drape the new belt over the drum and align it over the wear mark on the drum and the re-install the front panel. I added a couple of images below to reference.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
July 12, 2013
See more answers
Q:

Gas dryer won't run.

A:

Managemylife.com is a great place to find the answers to just about anything, especially on our laundry appliances. I'm sorry to hear that you are having some issues with your Kenmore gas dryer. I did some research at Managemylife website and found two expert answers to a similar question that may help until your expert can respond. I have attached the links below so you can check it out. Whirlpool is probably the manufacturer of your Kenmore dryer. The expert answer about a Whirlpool dryer may be helpful. I hope these links help you out.

Read More
James -
April 24, 2012
A:

I know that it can be very difficult to have issues with the dryer. This problem is usually due to the thermal fuse failing (#39 on image below). I would suggest that you replace this. You will need to access the back of the dryer to find the blower housing. The thermal fuse is on the outside of it. It is a small plastic part with two wires go to it. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
April 25, 2012
A:

Hi, thank you so much for your response. I will definitely try the thermal fuse. Is this something that can be tested with an ohm meter? Also, where do I find the "image below?" Should it show up as a link? I do not see it on my screen. Thanks again!

Read More
Ann -
April 26, 2012
See more answers
Q:

How do I light the pilot on my Kenmore gas dry model 11077950110

A:

I understand that you want to light the oven on your gas dryer. I have taken some time to research your question here on the Manage My Life website and I was able to locate a similar question to yours. I attached the link below for you to view while you are waiting on your response from an expert. I hope the link that I provided gets you one step closer to lighting your dryer. Have a great day.

Read More
Alina F. -
July 08, 2011
A:

Thank you for your help. As the link stated the Kenmore dryer model 11099750110 has electronic ignition and I just had turn it on and be patient. This was a restart after disconnecting the gas to replace the dryer belt. The flame takes a quite a few more seconds to be ignited by the glow plug when being restarted. So it works. I called my appliance tech and the first sentence in that link you sent confirmed what he told me. No wonder I couldn't find any info online for hours regarding "lighting the pilot" on this model. Doy!

Read More
jw -
July 08, 2011
A:

This particular unit does not have a "pilot" to light. It uses an ignitor that glows brightly to light the gas as the coils release it.

When the ignitor is not working on a gas dryer the most likely cause is a bad thermal fuse.

The thermal fuse is located on the rear exhaust tube and is accessed by removing the rear panel. See the image below for help with this.

Remember to unplug the dryer first.

The fuse can be checked for continuity if a meter is available or it can be bypassed for a moment to check if it is the problem.

You bypass the fuse by unplugging the dryer and removing the two wires on the fuse and joining them together. Use caution if you try this.

If the fuse is not the problem then likely the ignitor is the problem.

Check the fuse and reply with what happens for further assistance.

Read More
Fred M -
Sears Technician
July 09, 2011
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show