Model #11077062600 KENMORE ELITE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8557891 Burner Assembly, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

Dryer will not ignite 11077062600 Kenmore Elite Dryer

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dryer and I do understand your frustration. Glad to help out. I'm looking at your model number 11077062600 and from your description I suspect that igniter is bad. Here is a link that will help test the igniter and valve coils.  Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others. 

Read More
Sherman_G_Wallace -
Sears Technician
October 29, 2014
Q:

Gas Dryer

A:

Gathering information is always a good first step with home appliance repairs. The expert will review to provide help within two days. I was able to locate a similar question for this model that might provide some of that information. I added the link to Sears Parts Direct for the diagrams and parts list if needed. I hope these links help.

Read More
Barbara -
March 31, 2013
A:

Hi,

Thanks for contacting ManageMyLife. I understand how frustrating it is having trouble with your appliance not working.

On the gas dryer such as your model, the thermal fuse will, on a SINGLE motor model keep the heat turned off.  On a DUAL motor model the thermal fuse will keep both motor from operating.  This is possibly not the type dryer you may know.  I provide you the diagram and the way to get to the motor and the gas valve to check the thermal fuse mounted on the blower housing. 

NOTE:

  Always unplug or de-energize electrical equipment before removing covers or attempting service.

Be careful and wear appropriate hand protection when working around sharp metal parts.

 

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
April 02, 2013
See more answers
Q:

My Kenmore Elite Dryer M# (110.77062600) will not Heat... Everything else works. It just blows cold air

A:

Good afternoon.... I can fully understand your concern regarding this issue. I did locate a link that will discuss this situation in greater detail. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might be wrong with your dryer and have a nice day

Read More
Henry -
January 15, 2013
A:

Thank you for your question and I understand your concern.

There could be one out of many possible reasons why your gas dryer is not heating.

  • Faulty electronic control board
  • Faulty thermal fuse
  • Faulty thermal cut-off
  • Faulty hi-limit thermostat
  • Faulty flame sensor
  • Broken glow bar igniter
  • Faulty centrifugal motor switch
  • Faulty thermistor
  • Faulty gas solenoid coils

In order to access all but the control board, the front panel must be taken off to access the components listed above.

I added three images in my second response with the procedure of removing the front panel along with the wiring diagram. I traced the heating circuit and circled the components in the heating circuit. I would check the thermal fuse first if the glow bar igniter will not glow. If the thermal fuse is Okay, check the glow bar igniter for continuity. NOTE: Disconnect the power cord from the power source before servicing.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 17, 2013
A:

Tony: See images below.

Read More
Joey S -
Sears Technician
January 17, 2013
See more answers

Top Parts