Model #11076901692 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • 3402851 Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Is model no 11076901690 the same as 11076901692 11076901690

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about whether model 11076901690 and 11076901692 are the same. I will be happy to help you with this. These are the same dryer with some differences. When the dryer is first made, the last number of the model number is a zero. As the manufacturer makes changes, such as substituting a part or making a design change, the last number is rolled up one number. This means since the first production of this dryer under model number 11076901690 to the production of the 11076901692 model, there have been two sets of changes. It could be a single minor part or major changes. The change in model number does not tell us what has changed only that changes have been made. That is why it is very important to use your complete model number when ordering parts. 

I once found a tractor that the last number of the model number indicated the complete engine was substituted. The first one had a Briggs and Stratton, the second one had a Tecumseh and the third one had a Honda engine. Using the wrong model number in that case and you would definitely end up with the wrong engine parts. I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
June 29, 2015
Q:

Why won't my Kenmore dryer heat?

A:

The lack of an adequate gas supply is one common cause of this type of dryer not heating. Make sure that your dryer is properly hooked up to an adequate gas supply.

If the gas supply is okay, I recommend checking the thermal fuse next. This fuse is on the blower housing. You can access this fuse by unplugging the dryer and removing the bottom front service panel (see first image below). The thermal fuse will have red and red/white wires attached to it. Remove the wires from the thermal fuse. Using a volt/ohm meter, measure the resistance across the leads of the thermal fuse. You should measure near zero ohms of resistance. If you measure infinite resistance (open), then the thermal fuse is blown and will need to be replaced.

NOTE: If the thermal fuse was blown, check your dryer venting for clogs or restrictions.

If the thermal fuse is okay, you could have a component failure in the gas valve assembly. A bad motor switch or failed timer contact could also prevent the dryer from heating. A bad operating thermostat or high limit thermostat could also be causing your problem. A wiring failure between these components would also prevent the dryer from heating. The wiring diagram for your dryer is illustrated in the second image below.

If you need more help after checking the gas supply and the thermal fuse, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
September 12, 2008
A:

Thanks Lyle for the detective info. My no heat cause turned out to be an open THERMAL FUSE. (Thanks for the wire color identification) To get to it I removed the LINT DUCT ASSEMBLY by removing two mounting screws. This made access to the thermal fuse mounting screws easier but impossible to remove with normal tools due to the proximity of the dryer drum. My dear wife had given me tools as a present that included a KOBALT 23741 Magnetic Finger Bit Driver. This stubby quarter inch hex driver did the trick! Otherwise I would have to remove the Blower housing also. I guess this is done by removing the Blower Wheel? Thanks also to SEARS PARTS DIRECT.COM for having this customer comment page on their website.

Read More
Jon -
June 16, 2013
See more answers
Q:

Kenmore Gas Dryer quit working

A:

It is never a good time to have a Kenmore dryer that does not run. In the link below is information that may be helpful while waiting on an expert response to your specific model.

Read More
Anna T -
October 29, 2012
A:

Thanks for the inquiry about your dryer not starting. I will be glad to help with this issue.
Based on your description it sounds like the start button is working and the motor will not come on. I think the clicking sound must be the motor attempting to start but not completing the circuit to run. Replacing the motor would be needed as the switch is not available.
There are some test of the circuit that should be completed before making a final determination of the problem. I will attach below the wiring diagram and if you have testing equipment and tools as well as feeling confident in testing the circuits it will be helpful. Always disconnect power supply to the appliance before servicing and if testing live voltage be sure to wear proper safety equipment
If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .



Thanks Ron H.

Read More
Ron H -
Sears Technician
October 31, 2012
See more answers

Top Parts