Model #11076812695 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • 3402844 Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Dryer is not heating 11076812695 Kenmore Gas dryer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your dryer is not heating.


 Gas valve: 

Measure resistance of the following terminal:
  1. ? Valve 1 terminal 
  2. ? Valve 2 terminal
  3.  Resistance value : > 1.5kg ~
  4. ? Resistance value : > 1.5~2.5kg
ignitor:  Measure resistance of terminal
to terminal. Resistance value : 100~800?

Hi-limit Thermostat: 
Measure resistance of terminal to terminal:
  1. ? Open at 203 ± 7°F (95 ± 5°C)
  2. ? Close at 158 ± 9°F (70 ± 5°C)
  1. ? Resistance value ? ∞
  2. ? Continuity < 1?
Thermal Cut off: Measure resistance of terminal to terminal: 
  1. ? Open at 230 ± 12°F (110 ± 7°C)
  2. ? Manual reset
If thermal fuse is open must be replaced:
  1. ? Resistance value ? ∞
  2. ? Continuity < 1?

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

 

 

Read More
Natasha12 -
Sears Technician
July 06, 2015
Q:

liquid propane to natural gas convert back 11076812695 Kenmore Gas dryer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions.
Your Sears partsdirect expert will research your question and respond within two business days but usually sooner.
Thank you for using Searspartsdirect.com!

Read More
Henry -
April 30, 2013
A:

That dryer can be converted back to natural gas. The conversion should be completed by a qualified installer. 

 

If you did not save the natural gas orifice (part 234826) and the leak limiter cap for the regulator (part 694424), then you can order those parts from this page: Sears PartsDirect.com.

 

I posted some images below that show the instructions for the LP conversion kit that was used to convert the dryer to LP gas. That process will need to be reversed by the installer to convert the dryer back to natural gas. The bottom of the second image shows how to remove the front panel to access the burner assembly.

 

You can contact your local gas provider for a qualified installer to complete this conversion. You may also be able to find a pre-screened service provider on the ServiceLive.com  

website. 

 

 

 

 

If you need more help, reply with additional details and we will assist you further. 

Read More
Lyle W -
Sears Technician
May 01, 2013
See more answers
Q:

I have a kenmore 80 series dryer model# 11076812695 lately it's been taking longer to dry a load of clothes and now its up to about two hours. Any help please.

A:

I understand how frustrating it can make you if you have to wait 2 hours before 1 load is dried. I found this link in the Manage My Life website that might give you some answers. This answer from the expert will give you some suggestions, while your waiting on an expert response. I'm attaching the link below, I hope this helps!!!!!!!!! http://www.managemylife.com/mmh/questions/203460-what-would-cause-my-kenmore-dryer-to-take-2-hours-to-dry-a-load

Read More
Raquel F -
November 10, 2010
A:

I understand your concern. There is likely one of two possible failures causing long dry times. The most common failure is a restricted or blocked vent system. For testing purposes only: Disconnect the vent hose from the back of the dryer and dry one normal load of clothes. If they dry in the normal amount of time (60-70 minutes) then this test would verify a restricted venting system. NOTE: DO NOT leave the vent hose disconnected after running this test, reconnect the vent hose after testing.

If it continues to take a long time to dry with the vent hose disconnect then the other most common failure is weak solenoid coils which are mounted on top of the gas valve assembly.

In order to verify weak coils, pry the small square plastic inspection cover off located below the dryer door. Start the dryer and watch through the inspection hole and monitor the burner and the glow bar igniter. You will likely need to pull up a chair and monitor the burner operation until you see the red glow of the igniter come on a glow. If you ever find the glow bar glowing bright red and then fade OFF without any burner ignition, replace both solenoid coils sitting on top of the gas valve assembly.

I added instructions in the images below.

The solenoid coil kit is part #279834 and can be ordered from Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
November 11, 2010
A:

Do gas dryers exhaust combustion products through the venting as well as moist air? What I mean is, it is it safe to disconnect venting from a running gas dryer? (It may be, I just don't know). I think a carbon monoxide detector would in order just in case! Remember if the problem is beyond your capability to solve, you can call Sears service 24/7 1-800-469-4663.

Read More
LookOver1 -
November 11, 2010
See more answers

Top Parts