Model #11076712695 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • 3402844 Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

when i pushthe start button on my gas dryer with nothing in it, it starts up and runs, but when i put wet clothes in it and push the button,it hums and 110.76712695

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore dryer.

From the information you have provided above, I can understand the frustration of having your dryer malfunction, after researching model number 110.76712695. It seems to me like the motor may not be strong enough to rotate the drum with clothes in it, that’s why when you take them out it does. Id suggests checking the belt make sure it’s on and working properly.  I would suggest replacing the motor to the unit to see if that fixes the issue. The part number for the motor is 279827.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting www.SearsHomeService.com*

Read More
Benny23 -
Sears Technician
May 13, 2015
Q:

What would cause my gas dryer to fail to ignite after the first initial burner ignition?

A:

Based on your symptom; the coils on the gas valve becomes weak after the initial burner ignition. Replace both solenoid coils at the same time and your dryer will likely operate normally again. The part number for the coil kit is #279834. You will need to remove the lint filter and remove the screws under the lint filter. The top will need to be hinged open and the front panel will need to be removed in order to access the burner assembly and coils. See images below for instructions. NOTE: Disconnect the power cord from the power source before servicing the dryer.

Read More
Joey S -
Sears Technician
September 11, 2009
A:

I have the same problem but the only difference is that I did replace both coils and I'm still having the same problem (ignitor lights but no gas flow). What is causing it not to get gas now?

Read More
Chad -
September 25, 2013
See more answers
Q:

Why is my gas dryer not heating?

A:

Without the model number I can only give you general information.

There could be several causes of your dryer to not heat:

  • Broken igniter.
  • Flame sensor.
  • Thermal fuse.
  • Electronic control board.
  • Heater relay.
  • Thermistor.
  • Gas valve coils.
  • Motor switch.
  • High limit thermostat.
  • Temperature switch.

If more information is needed please resubmit your question with the complete model number and more details.

Read More
Jerome G. - Personal Solutions Manager -
Sears Technician
March 29, 2010
A:

My model is Kenmore 70 series gas dryer #110.76712695 the heat won't come on

Read More
bill -
August 26, 2010
A:

Bill, I recommend that you check the gas supply first. Make sure that the gas cut-off valve is fully open and that you have adequate gas pressure supplied to the dryer. If the gas supply is okay, click on the link below and follow the advice on pulling the observation plug to view the gas valve assembly. If the igniter is not glowing, I recommend that you check the thermal fuse and other components in the circuit shown in the link below. If the igniter is glowing and then cycling off to initiate the ignition process, then your likely failure is in the gas valve coils (kit part 279834). If you need more help, let us know.

Read More
Lyle W -
Sears Technician
August 27, 2010
A:

Hey, does the dryer start up at all and begin to run, but just doesn't heat up? If so you may want to check the exhaust and make sure that it isn't clogged or otherwise blocked. That will prevent the machine from heating and running properly.

Read More
Troy -
November 15, 2010
A:

I have a kenmore gas dryer model#11070912990 that is blowing out cool air, please advise.

Read More
dee -
April 16, 2011
A:

For Dee: The information in the link provided below my August 27, 2010 posting should be helpful. Your dryer is slightly different than the one described in that link but the gas valve assembly is the same. Check to see if the igniter is glowing while the dryer is running in a heated cycle. You can remove the bottom front service panel as shown in the first image below if the dryer does not have an observation plug. If the igniter is not glowing, I recommend that you UNPLUG the dryer and check the thermal fuse. The location of that component is shown in the first image. The second image shows actual pictures of your type of dryer. I provided a link for a video that shows how to test the thermal fuse. If that fuse is blown, it will need to be replaced. Also, check the exhaust vent system as shown in that video if the thermal fuse was blown. You can order parts from the Sears PartsDirect.com website (see link below). If the igniter is glowing and then fading off but the burner will not ignite, then your problem is likely caused by failed gas valve coils (kit part 279834). These tips may help you resolve this heating problem in your dryer. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
April 19, 2011
A:

I have a Kenmore Elite gas dryer, model #11073032101 and I have no heat. It tumbles just fine, but blows cold air. I know this because if I run it enough times, the clothes will eventually dry, but it is probably costing me out the whazoo in electricity. Can you please help?

Read More
Shelli -
September 14, 2012
A:

Hello Shelli. The image below shows the theory of operation for the gas valve assembly on your dryer. You will need to determine whether the igniter is glowing and then fading off while the dryer is running in a heated cycle. You may be able to see the glow of the igniter through the bottom of the dryer cabinet with the lights for the laundry room off. If not, you may need to remove that bottom front service panel and briefly run the dryer with that panel removed to observe the igniter. (Unplug the dryer to disconnect electrical power as soon as that brief test is completed. Replace the panel.) If that igniter is glowing and fading off properly as described in the theory of operation then you probably will need to replace the gas valve coils (kit part 279834). If that igniter is not glowing then you could have a blown thermal fuse on the blower housing. The information shown in the posts above should help you access components and repair those problems. These are the 2 most likely failures that would prevent that gas dryer from heating. If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
September 17, 2012
A:

Lyle, my dryer model #11070942990 is experiencing the same problem. Running fine, I have deep cleaned the unit and the exhaust pipe, etc. No heat on any cycle. I am going to check the thermal fuse now but what else do you advise? Thank You, Bob

Read More
Bob -
October 29, 2012
A:

Hello Bob. See if that igniter is glowing and fading off as shown in the theory of operation image that I provided above. If that igniter glows, then the thermal fuse should be okay. If the igniter glows and fades off then the gas valve coils (kit part 279834) will probably be needed. If the igniter is not glowing, then checking that thermal fuse is definitely a necessary step in troubleshooting this problem. If the thermal fuse is okay, you could have a bad heater relay, a failed control board, a bad thermistor (temperature sensor), a failed igniter, a bad flame sensor or a wiring failure in that circuit. The image below shows a wiring diagram for that dryer with the circuit through the igniter traced in red. I hope that this additional information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
October 29, 2012
See more answers

Top Parts