Model #11075922401 KENMORE ELITE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts And Optional Parts (not Included)
    3 Results
  • 8318276 Burner Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

Testing coils? 110.75922401

A:

Thank you for your inquiry on your Kenmore Dryer, Model: 110.75922401. From reviewing the details on your model, I have provided a link to a couple of videos on similar models of dryers, which should be able to assist you in troubleshooting the coil valves.

Click Here

Safety Warning: Before beginning the repair, disconnect the direct power supply to the dryer to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
May 07, 2015
Q:

Dryer drum won't turn 11075922401 Kenmore Elite Residential dryer

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

The issue could be with the spinning portion of the dryer. I would recommend in replacing the drum roller guides, belt and tensioner. If these aren’t the issue it could be the motor. Hope this information has helped you. Again, thank you for choosing SearsPartsDirect.com.

Read More
JeffwallaceIII -
Sears Technician
December 10, 2014
Q:

Kenmore dryer model number 110.75922401 flame/gas won't stay on.

A:

I know how important it is to have a good working dryer in your home so that you can keep your clothes nice and dry. While you are waiting for an expert answer, I did manage to find a link that will provide you with some good tips about what may be causing your problem. I hope my link is useful.

Read More
Joseph P. -
March 14, 2011
A:

Thank you for your question and I understand your concern.

Based on your symptom and details the high limit thermostat (key#43) could be causing the gas valve to close and shut the burner off. See image below.

The high limit thermostat is mounted on the burner funnel and its purpose is to shut the burner off if there is a restriction in the venting system. When there is a lack of airflow the burner flame will not be drawn straight back inside the burner cone and cause the high limit thermostat to open/break the circuit and cause the gas valve to shut off.

I would suspect the high limit thermostat is opening and causing your symptom. For testing purposes you could disconnect the two wires from the high limit and connect the two wires together making sure they don't touch any metal/ground and then see how long the burner stays on. The exhaust temperature should average around 150 degrees when set on high heat when the dryer is operating correctly. NOTE: Do not leave the high limit jumped out; replace it if you find it faulty. Be sure to disconnect the power cord from the power source before servicing your dryer.

Read More
Joey S -
Sears Technician
March 16, 2011
A:

It turns out that I didn't do a good job cleaning the lint in the exhaust line. The homebuilder put in THREE 90 degree turns and the lint had collected close to the end ( where it exits out through the attic vertically). I Had cleaned out all the lint with a 20 ft flexible rod (4 5 foot attachments) that I used my drill to turn. Thought that was good enough, but not quite! Once I cleaned out ALL the lint at the end of the exhaust line, everything worked! Moral of the story: clean out the entire line especially if the home builder is an idiot and works in 3 90 degree turns ! Paul

Read More
Paul -
May 01, 2011
A:

My dryer was working fine on Friday, and then Saturday, it wasn't. I allowed my son and his roommates to use the machine for their laundry (I think they were doing loads that were far too large). Right now, the dryer turns on, heats up, and will spin very slowly if there is only a couple of light items in the drum. If I load the drum completely, it won't turn at all. I can spin it by hand, and it will start and spin for a while, but then stop. When it actually does spin, it makes a laboring sound, like slow motion spinning. I would prefer to fix the issue myself and not have to bring in a service person. What could this be?

Read More
Natalie -
December 08, 2014
See more answers

Top Parts