Model #11074672400 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8318272 Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Seal? 11074672400 Kenmore Residential dryer

A:

Thank you for choosing sears I would be happy to help you with your dryer. Upon researching model 11074672400; the door seal part# 3405246, I have posted a link below of the door seal key#57.

I trust that this information will help you, thank you have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
November 11, 2014
Q:

kenmore gas dryer won't heat up.

A:

 

 Thank you for your question and I understand your concern.

 

I added an image below of the wiring diagram. I circled each one of the components that must measure continuity in order for the igniter to come and glow. If all the components on the back of the dryer test O Ohms/continuity, then you will need to disconnect and check the flame sensor and the glow bar igniter for continuity. The flame sensor is mounted on the side of the burner cone.

 

If your certain all the components measure continuity, and be sure to disconnect at least one wire from the component before testing it for continuity, the timer contact BK and R may not be closing to complete the voltage supply to the red wire that connects to the high limit thermostat and the rest of the components connected in circuit.

 

You can remove the wire connected to terminal BK and R at the timer. Set the timer dial to "Time Dry" check across the two terminals (BK and R) for continuity. If the Ohm meter measures continuity and all the other components in the circuit measures continuity, then it is possible that the motor centrifugal contacts M2 and M1 are not closing when the motor is running to complete the Neutral path to the burner assembly.

 

Now, just to let you know, a component can measure continuity with no load/current but it can open up under current draw. You may want to try placing a jumper wire between the two wires connected to the component and see if the igniter will glow. If it doesn't, reconnect the two wires and jump across the next component in the circuit. If the igniter will not come on and you know the igniter and all the components and timer are okay, then the motor centrifugal switch contacts 2M and 1M are not likely closing when the motor is running. NOTE: Be sure and disconnect the power cord from the power source before servicing and testing/jumping the components.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.


Read More
Joey S -
Sears Technician
October 02, 2013
Q:

kenmore dryer 110.74672400 will not heat

A:

Having a properly working dryer is very important. I found some information for you that I am hoping will be able to help you. I am adding the link below to help you with your question while you wait for your expert response. I do hope that this will help you out.

Read More
Marc -
August 20, 2012
A:

I know that it can be very frustrating to have issues with your dryer. From the description you give the problem is with the coils or the gas valve itself. If the igniter keeps cycling on and off then the thermostats and thermal fuse are okay. One thing to listen for is a click/hum/buzz from the coils when the igniter clicks off. When the flame sensor removes the voltage from the igniter it immediately sends it to the coils to open the valve. If you hear something from the coils then most likely the problem is with the valve. If you hear nothing from the coils then the coils may indeed have broken down as they heat up.

This can be difficult to check since everything works initially but I'd suggest changing the coils for this problem. The 8318277 valve will cost approximately $100 dollars and which is little steep for part that might be the problem. I suggest replacing the coils because the 279834 coil kit with both coils only costs $20 dollars which is more reasonable and cheaper than each coil individually. The coil kit can be obtained from the following link: Sears Parts Direct . If you don't feel comfortable doing this yourself, just click on this link to schedule service: Sears Home Services . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
August 21, 2012
A:

You are a life saver. Replaced coils and now I have heat. Thank you Thank you.

Read More
wayne -
August 23, 2012
A:

I happy that you were able to get this working! Please let me know if you need anything else. Thank you for using Manage My LIfe.

Read More
AnneJ -
Sears Technician
August 24, 2012
See more answers

Top Parts