Model #11074652400 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8318272 Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Drier ignites when started but then loses ignition. 110.74652400

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your dryer. Upon researching model 110.74652400; check if the igniter is glowing. The igniter sends power to the coils once it reaches a certain temperature. The coils would send gas then stop after a couple seconds to a couple minutes. Then it may do the same thing a couple more times or it may stop. I would look at the coils if this kind of symptom is occurring.

Thank you for choosing Sears Parts Direct. We appreciate your business. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
August 05, 2015
Q:

Natural Gas Convertion

A:

Manage My Life is a great website to speak directly to an expert who can help you every step of the way to solving the problem you are having. An expert shall have an answer to your question within 24 to 48 hours. Have a great day.

Read More
Alina F. -
September 22, 2011
A:

The part number for the orifice on your dryer burner is 234826, and the price is $11.13.

The right front burner on your range uses orifice part number 316237901, and the price is $14.36. The other 3 top burners use orifice part number 316237902, and the price is $13.99 each.

The oven burner orifices are adjustable. Turn the orifice counter clockwise about 1-2 turns and light the burners. Adjust the orifice until the blue part of the flame is about 3/4-1 inch long.

Read More
Jimmy K -
Sears Technician
September 24, 2011
A:

The parts are to convert it back to Natural Gas correct. Just making sure. Thank You Very Much!!

Read More
Timothy Canale -
September 24, 2011
A:

Timothy, yes the part numbers are for the natural gas orifices for the top burners of the range and the burner of the dryer. Thanks for using Manage My Life.

Read More
Jimmy K -
Sears Technician
September 24, 2011
See more answers
Q:

Kenmore gas dryer ot heating correctly

A:

I'm very sorry about the difficulties that you are experiencing with your dryer. I did some research at managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond. I have attached the link below. If you would like assistance from a qualified technician I have also attached a link to searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
January 08, 2011
A:

Thank you for a good description of the problem. From what you described I suspect poor airflow. This will also explain why the thermal fuse failed last time. If the venting is restricted or runs too long before going outside this will cause the thermal fuse to fail. I recommend removing the vent hose & with an empty dryer check the air temperature with a thermometer. The heat should run between 150 to 190 degrees before cycling off. If you do not have these temps I recommend replacing the operating thermostat. Another possibility is the gas valve or a wiring problem. I am sending you an image showing the location of the operating thermostat.

Remember to disconnect power before attempting access.

The first responder's link is not for this model.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: sears home service

Read More
biker dave -
Sears Technician
January 10, 2011
See more answers

Top Parts