Model #11074632301 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8318272 Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My sears kenmore dryer will run but no heat

A:

I can understand your frustration over your dryer not heating. I did some research and provided a link to a similar question and answer on our site. I hope this will shed a little more light on the issue until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
May 23, 2013
A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. If the gas dryer is not heating you could be experiencing an issue with the thermal fuse (key#39), operating thermostat (key# 41), high limit thermostat (key# 34), thermal cut-off (key# 12) or the burner assembly which consist of the igniter (key# 4) and the gas coil valves (key# 13 & 14)(image three). The ignitor must have 110-120 volts supplied to it or it will not glow. The ignitor has glow before it'll cause the gas valve to open and have burner ignition. If you have an ohms/volt meter you can test all these parts for the proper continuity. To test the parts, disconnect both wires from the components and test them at room temperature. The ohms reading for these components are the following:

  • Igniter (p/n: 279311) 40 ohms
  • Thermal Fuse (p/n: 3392519) 0 ohms
  • Operating Thermostat (p/n: 3387134) 0 ohms
  • Thermal Cut-Off 0 ohms
  • High Limit Thermostat 0 ohms
  • Gas Coil Valve1 560 ohms
  • Gas Coil Valve2 1220 ohms

The gas coil valve kit include both valves and is part number 279834. The thermal cut-off kit includes the high limit thermostat and it is part number W10480709. The wiring diagram for your dryer is provided in the first image below and the second image will assist you disassemble the unit to access these parts. You can order parts from our Sears Parts Direct web site. I hope this information helps. Please reply back to this thread if you require further assistance with this repair. If you do not feel comfortable performing test or repairing this problem yourself, I recommend scheduling for service. You can schedule for service online with our Sears Home Services team. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
May 24, 2013
See more answers
Q:

kenmore dryer model number 110.74632301

A:

I'm sorry to hear that you are having some difficulties with your dryer . I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. I hope this link provided assist you.

Read More
Jackie S -
October 28, 2011
A:

Sorry for the dryer problems. This can be a good do-it-yourself project if you're willing.

From the description you give I suspect the problem is with the gas valve or gas coils.

As long as the ignitor is glowing the thermal fuse is okay. Even though there is no flame the ignitor should continue to cycle on and off. There is a small square plug on the front panel that can be removed. From the hole you can see if the ignitor continues to cycle on and off even though there is no flame.

If the problem is the valve or coils then it will be difficult to determine which is the problem since there is a flame at the beginning.

One way to consider the problem is that a coil kit can be obtained for about $25 dollars while a valve would cost over a $100 dollars. The 279834 coil kit can be obtained for about $23 dollars at the following link: Coil Kit .

I can also provide you with some step by step to access the valve if needed. Remember to unplug the dryer first. The image below will help you access the valve.

I hope this helps. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
October 29, 2011
See more answers
Q:

Dryer heat not staying after High limit thermostat replaced

A:

Diagnosing dryers can take patience. I found a similar question for your model from a previous expert post that may help while you wait for the expert. I attached the link below. Hope this helps find the cause.

Read More
Barbara H. -
November 27, 2010
A:

You say the flame stays on a few minutes but then goes off. The key question is does the igniter come back on.

If the igniter never comes back on then the problem will be with the timer or one of the thermostats.

Most likely the igniter is coming on and clicking off but there is no flame. You can check this by removing the small square plug on the front panel so you can take a peek.

If the igniter comes on and clicks off but there is not flame then most likely the problem is with the gas coils or gas valve.

You can reply to me about what the igniter is doing for further assistance.

Read More
Fred M -
Sears Technician
November 29, 2010
See more answers

Top Parts