Model #11074622300 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:



Question and Answers


Capacity size 11074622300 Kenmore Gas dryer


Thank you for choosing and being a valued member. I can certainly assist you.

I do apologize due to the age of the product we do not have the cubic feet of this dryer. You will need to measure the unit in order to determine cubic feet. 

29 inch wide dryer.

Click here to how to measure.

You can also visit for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
June 11, 2015

how to replace drive belt 11074622300 Kenmore Gas dryer


Hello glad to help.  Thank You for choosing Sears
I am sorry and do understand your frustration when needing to replace the belt.
Glad to help out.   Im  looking at your Kenmore model number 110.74622300.

1.  Please unplug the dryer.  Lift the lint filter out from the top.  Remove the 2 screws nest to the filter compartment.
2.  Slide a blade or use a putty knife into the gap between the front and top panels.  Press the putty knife into the spring clips located about 2 inches from each end.
3.  Lift the panel up and cack to rest on the wall behind for support.
4.  Remove the screws along the top of the front panel.  Lift the front panel straight up and dislodge it from its base.   Set the front panel aside.
5.  Move the idler arm towards the front of the dryer to loosen the old belt.  Slide the old belt off of the drum and the pulleys.
6.  Position the new belt around the drum and pulleys.  Move the idler arm toards the drum until the belt is tight.
7.  Reposition the front panel.   Install the 2 screws along the top of the front panel.
8.  Lower the top panel back into its former postion and put things back as normal

If you have further questions please let me know.
Thanks for choosing Sears

Read More
Larry L -
Sears Technician
February 18, 2014

Why won't my Kenmore gas dryer heat?


The wiring diagram for your model of dryer is illustrated in the first image below. Several components can prevent the dryer from heating. If the igniter is not glowing to initiate combustion in the burner assembly, then I recommend checking the thermal fuse and the thermal cutoff fuse first. To access and check these components, follow these steps:

  1. Unplug the dryer to completely disconnect electrical power.
  2. Shut off the gas supply to the dryer.
  3. Remove the back panel of the dryer.
  4. Locate the thermal fuse. It is on the blower housing (Key 39 in the second image below).
  5. Pull the wires off of this fuse.
  6. With a volt/ohm meter, check the resistance across the leads of this fuse. You should measure new zero ohms of resistance if the fuse is okay. If you measure infinite resistance, then the fuse is blown and will need to be replaced.
  7. If the thermal fuse is okay, then check the thermal cutoff fuse in the same manner. The thermal cutoff is on the heater box (Key 12). If it is blown, it will need to be replaced.
If both of these fuses are good, then I recommend checking the high limit thermostat (Key 34) and the operating thermostat (Key 41). These can be checked in the same manner as the thermal fuse and the thermal cutoff.

If all of these components are okay, then you could have a bad flame sensor or a bad igniter. A wiring failure could also prevent the igniter from glowing. A timer contact failure could prevent voltage from being supplied to the igniter. A bad drive motor switch could interrupt the neutral side of this circuit.

If the igniter is glowing to initiate combustion, you could have bad gas valves in the dryer or a bad flame sensor.

I recommend conducting the tests noted above and then resubmit your question with additional details if you need more help with this dryer heating problem.

Read More
Lyle W -
Sears Technician
July 11, 2008

All fuses and thermostat check out. Still no glow on ignitor. Can hear gas valve solenoids clicking. Air blows and drum turns. No glow

Read More
Steve -
September 07, 2013
See more answers

Top Parts