Model #11072952100 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
  • Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

How do I get to the thermal fuse? 11072952100 Kenmore Dryer

A:

Thank you for choosing Sears Parts Direct. I can certainly assist you in locating the thermal fuse on your dryer. I did look into the model number you have provided, and I have found information to assist you. 

I have attached the images to access and test the thermal fuse. 

Let me know if these help.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services.

Thank you for your question. Have a great day.

Read More
Natasha12 -
Sears Technician
July 24, 2014
Q:

no glow at heater replaced thermal fuse, no 120vac at starter 11072952100 Kenmore Dryer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Dezeray S -
June 03, 2013
A:

tried that over weekend, they dropped my conversation

Read More
jack -
June 03, 2013
A:

Thank you for your question.  I am sorry you are having a problem with your Kenmore 110.72952100 Gas Dryer.  The heater relay in the console would be the place to start.  This dryer has a heater relay and a motor relay.  Both are the same part and work in the same way.  The heater relay has 2 heavy red wires and two smaller R/W wires.  To bypass the replay for a moment to check the heating problem would require removing the two heavier Red wires and joining them together.  Remember to unplug the dryer first.  A small piece or insulated wire with two bare ends is the best by to bypass the relay.  If the dryer heats then the relay or control board is likely at fault.  The relays can even be swapped to check.  I hope this helps.  You can reply below with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
June 06, 2013
A:

Thank you for your question.  I am sorry you are having a problem with your Kenmore 110.72952100 Gas Dryer.  The heater relay in the console would be the place to start.  This dryer has a heater relay and a motor relay.  Both are the same part and work in the same way.  The heater relay has 2 heavy red wires and two smaller R/W wires.  To bypass the replay for a moment to check the heating problem would require removing the two heavier Red wires and joining them together.  Remember to unplug the dryer first.  A small piece or insulated wire with two bare ends is the best by to bypass the relay.  If the dryer heats then the relay or control board is likely at fault.  The relays can even be swapped to check.  I hope this helps.  You can reply below with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
June 06, 2013
See more answers
Q:

Kenmore Elite electric dryer Model # 11072952100. The dryer runs but does not heat up.

A:

I understand the important role a dryer plays in having your clothes smelling fresh so it is important that your dryer not only runs but also heats. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
July 14, 2012
A:

Hi Dee,

Thank you for submitting a question to Manage My Life.

You did not mention whether or not the ignitor will glow. I recommend that you check to see if the igniter is glowing. To do this you will need to remove the toe panel and start a medium load of wet clothes. If the igniter glows you most likely have an issue with the gas valve assembly. If the igniter does not glow, the next thing I recommend is bypassing the heat relay on the control board. Or if you have an ohm/volt meter I am including the no heat checks in the images below. Working with live electrical current can be very hazardous and possibly deadly. Testing voltage output requires working with electrical current. Do not attempt this measurement without the proper tools and safeguards. If you are not sure you can make these checks safely, please refer this work to a service tech.

To bypass the heat relay (with the dryer unplugged) remove the wires on the heater relay and place a bypass wire across the two wires. Tape this connection very well with electrical tape so that it will not touch anything else. Plug the dryer back in and start a heat cycle. If the dryer heats, the thermistor or the control board will need to be replaced. The only way to check to see which one it is with a meter. The thermistor will need to be ohmed as shown on the sheet below. Do not leave the heater relay bypassed and continue using the dryer. This is for testing purposes only.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website; Sears Home Services .

Here is a link that you may use to view the parts list diagram or purchase any parts needed for your Kenmore model number 110.72952100 dryer .

I hope this is helpful. Check the things I have covered here and if I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
July 17, 2012
See more answers

Top Parts