Model #11070212990 KENMORE Residential Dryer

  • Cabinet
    3 Results
  • Top And Console
    3 Results
  • Bulkhead
    3 Results
  • 3402844 Burner Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

dryer takes too long to dry 11070212990

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore dryer.

From the information you have provided above, I can understand the frustration of having your dryer malfunction, after researching model number 110.70212990. You will need to watch and monitor the glow bar igniter operation for at least 15-20 minutes or until you find the glow bar glowing bright red and then fading off without any burner ignition. If you find the glow bar glowing and then fading off without any burner ignition, replace both solenoid coils which are mounted on top of the gas valve assembly.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting www.SearsHomeService.com*

Read More
Benny23 -
Sears Technician
June 10, 2015
Q:

Why is my dryer not heating model

A:

It is difficult to adjust without a Washer and Dryer especially when we use it daily. While you are waiting on an expert to answer your question, I found some great links in the Manage My Life website. I have attached the links below. Hope this helps!

Read More
Dezeray S -
March 26, 2012
A:

The thermostat with 4 wires can be checked for continuity across the two red wires. The smaller violet/purple wires have no function for the heating circuit. The most likely cause of the no heating problem would be the thermal fuse located on the blower housing in the rear of the dryer behind the rear panel. The image below will show you how to access the thermal fuse. If the dryer heats at all then the thermal fuse is not the problem. I believe the other thermostat you ask about is the radiant sensor. It can be checked for continuity. If the circuit is open then the ignitor will not work. You can obtain the thermal fuse from the following link: Thermal fuse for Kenmore dryer model 110.70212990 . I hope this information is helpful to you. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
March 26, 2012
See more answers
Q:

Kenmore Dryer Squeaking

A:

A Dryer is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Priscilla V -
November 21, 2011
A:

I'm sorry to hear that you are having some difficulties with your dryer . I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
Jackie S -
November 21, 2011
A:

Hi Scott,

Thank you for submitting a question to Manage My Life.

This is most likely an issue with the drum rollers. Here is a video that demonstrates replacing them; Video . Use this to help you locate the sound. Once you get the front panel off, roll the drum by hand and try to locate the squeak. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. This video is for demonstration purposes only. The dryer in this video may not look exactly like yours, but the procedure is basically the same.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. Check the things I have covered here, and if I may be of further assistance as more details become available, please reply to this post.

Landell

Read More
Landell -
Sears Technician
November 22, 2011
See more answers

Top Parts