Model #11069902890 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Manufacture dates 110.6992890 110.28922790

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your laundry appliances. Upon researching the model number provided;  model#11069902890 this model is from 1998, model# 110.28922790 is from 1997.

 

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
June 14, 2015
Q:

heating element 11069902890

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you in locating the instructions to replace the heating element on your dryer. 

I have attached the instructions to access your heating element.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
May 29, 2015
A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you in locating the instructions to replace the heating element on your dryer. 

I have attached the instructions to access your heating element.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
May 29, 2015
A:
Natasha12 -
Sears Technician
May 29, 2015
See more answers
Q:

Thermal fuse blows after about 5 minutes (3 times total) 11069902890 Kenmore Electric dryer

A:

Thank you for your inquiry on your Kenmore Dryer, Model: 110.69902890. From reviewing the details on your model, If you did not find any obvious problems in the exhaust vent system to the outside of the home, then I recommend conducting the following test: Before replacing the thermal fuse again, try these steps: Unplug the dryer to disconnect electrical power. Temporarily tape the two wires that go to the thermal fuse together to essentially "bypass" or "jump" the thermal fuse. Use electrical tape to properly insulate the connection and avoid contact of bare wire contacts with the dryer cabinet. NOTE: Do not leave the thermal fuse bypassed following this temporary diagnostic test. The thermal fuse is an essential safety component that must normally be in place to safely run the dryer. Reassemble the dryer and plug it back in. Fill the dryer with a medium load of wet laundry. Clean the lint screen and make sure it is properly in place in the lint screen housing. Pull the flexible exhaust vent hose off of the back of the dryer so that it will vent directly into the laundry room. Position the dryer so that you can measure the temperature of the exhaust air from the middle of the vent in the back of the dryer with an accurate thermometer. Start the dryer on a timed cycle with high heat. Measure the temperature of the air coming out of the middle of the exhaust vent behind the dryer. The dryer should heat up to about 150 degrees. The heating element should then shut off until the temperature decreases 15 to 20 degrees. The element should then cycle back on. The dryer should continue to cycle between about 130 to 150 degrees. If the dryer heats up way past 150 degrees, then you will likely need to replace the operating thermostat that is right beside the thermal fuse. You could also have a heating element that is shorted to the cabinet and heating constantly. NOTE: Stop the dryer if it heats past 180 degrees. Do not let it continue to run and heat past this temperature. If the dryer is cycling properly with the vent hose disconnected, then the likely cause of your thermal fuse blowing is the vent duct system to the outside of the home.

Safety Warning: Before beginning the repair, disconnect the direct power supply to the dryer to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
April 16, 2015

Top Parts