Model #11069422800 KENMORE Residential Dryer

  • Cabinet Parts
    3 Results
  • Top And Console Parts
    3 Results
  • Bulkhead Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Dryer 11069422800

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your dryer. Upon researching model 11069422800; you can unplug the dryer power cord and remove the heat element, thermostat, thermal fuse when the dryer is not hot. With the mentioned parts removed you can test the parts for continuity using a multi meter. The parts test should read continuity if the parts are ok, if one of the mentioned parts test reads no continuity then that part may need to be replaced. The mentioned parts work together to make sure that the dryer is successfully heated as needed so when any of the mentioned parts fail it will directly affect the heat.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
July 02, 2015
A:

what is a multi meter, and where do i get one?

Read More
ANGELA -
July 02, 2015
See more answers
Q:

kenmore dryer dosen't run

A:

The dryer not working can be very frustrating. I found some information for you that I am hoping will be able to help you. I am adding the link below to help you with your question while you wait for your expert response. It may take two business days for your expert to respond. I do hope that this will help you with the dryer.

Read More
Marc -
January 28, 2013
A:

I may need a few more details to help you resolve this problem. If an electric dryer will not run then the first part to check would be the thermal fuse. I also suggest you check the drum light. Does the drum light work when the door is open? The push to start switch may have failed. The push to start switch and door switch can be checked with a meter if one is available. You can reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
January 29, 2013
See more answers
Q:

Kenmore 400 dryer won't start.

A:

Providing a more detailed question including a model number will definitely help an expert better your search. If you would like to resubmit your question I would be more than glad to help you. Have a great day!

Read More
Alina F. -
October 10, 2010
A:

There are several different types of Kenmore 400 Series dryers. Since you did not provide a model number, I will assume that you have an electric dryer such as model 110.69422800.

Check the house circuit breaker for the dryer to make sure that it is not tripped.

On this type of dryer, the door switch could be bad or you could have a blown thermal fuse that would prevent the dryer from running. Less frequent possibilities for failures include a bad timer, a failed push-to-start switch, a wiring failure or a bad drive motor.

Check to see if the drum light turns off when you push the door switch in to simulate the door being closed. If the light does not turn off then the door switch is likely causing your problem. You can order a new door switch from the Sears PartsDirect website. Use the full model number of your Kenmore 400 Series dryer to access the parts listing for your dryer and order the correct part. The first image below shows how to open the cabinet to access the door switch. Be sure that you unplug the dryer before accessing internal components.

If the door switch appears to be okay, you can check the thermal fuse by unplugging the dryer and removing the back panel. If you have a volt/ohm meter, you can check the continuity through this fuse. Remove one wire and measure the resistance across the leads of the fuse. You should measure near zero ohms of resistance if the fuse is good. If it measures Ol (open load or infinite resistance) then it is bad and will need to be replaced. You could also test it by taping the wires going to this fuse together with electrical tape. Reassemble the dryer and see if it runs with this fuse bypassed. If it does then this fuse will need to be replaced. NOTE: Do not continue to run the dryer with this fuse bypassed. It is an important safety component that must be replaced. Also, check the exhaust vent duct system for a clog or restriction if the thermal fuse was blown. An resolved restriction in the air flow out of the dryer could cause the fuse to blow again shortly after it is replaced.

If the thermal fuse is okay, then you could have one of the less frequent failures listed above. If you need more help (or have a different type of dryer), reply with additional details and we will assist you further. Please include the full model number of your dryer in subsequent replies.

Read More
Lyle W -
Sears Technician
October 12, 2010
A:

Thank fpr the onfo on the thermal fuse, we bypassed the fuse and the dryer came on so now we know what to replace thanks agaian.

Read More
Eric -
January 28, 2013
See more answers

Top Parts