Model #11068942892 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Lamp size

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about the size of the lamp for your dryer. I am so sorry the information on the lamp cover and the information in the manual are conflicting. We will be happy to research this issue for you but will need some additional information. Please resubmit your question with the model number of the dryer included. You can normally find the model number on the facing of the dryer. It is hidden when the door is closed. 

Once we have the model number we will be happy to locate the lamp information for you. We look forward to your reposted question and the opportunity to resolve this question for you. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
February 07, 2015
A:

110.68942892 Thank you

Read More
Roger -
February 09, 2015
A:

the model number for this dryer is 110.68942892, as I stated before. I am still waiting for your answer as to the correct bulb. The plastic cover over the bulb on the dryer frame states 15 W, 110 v bulb only. the parts instruction manual calls for 25W 110 V bulb only. Please advise. Roger Wright

Read More
Roger -
February 11, 2015
See more answers
Q:

dryer does not heat anymore and keeps going and going

A:

Providing a complete model number to your question will definitely help an expert better your search. If you would like to reply to this thread with a model number included I would be more than happy to assist you. Have a wonderful day.

Read More
Alina F. -
May 08, 2011
A:

Kenmore 90 plus series Mod # 11068942892

Read More
Michael -
May 08, 2011
A:

Thank you for your question and I understand your concern.

Your dryer is not an average type dryer with the average type of controls. It has an electronic control board inside the console referred to as the "Evenheat" control board along with a timer and heater relay. It also uses a thermistor which is used to monitor temperature which works in conjunction with the evenheat control board. I added an image below with general information. I recommend calling a service technician to diagnose and repair your dryer.

Based on your symptom it could have one of many different component failures preventing the timer from advancing and from heating.

It could have a faulty "Evenheat" control board or timer. There is a very slight possibly it's not heating because of the lack of proper voltage, faulty heating element of thermal cut off. Locate the house circuit breakers dedicated for the dryer and reset both circuit breakers by flipping them OFF and ON 2-3 times and then check the dryer for heat. If it continues to run and not heat I recommend calling a service technician.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
May 09, 2011
A:

I have maytag, dryer it lost the heat .# - MD SDE305 DAYW - S/N # 18108396GC

Read More
Dara -
July 26, 2011
A:

Dara: Since your dryer is electric and the heating element required 220 volts to produce heat the first thing to check is the two house circuit breakers dedicated for the dryer. Reset both circuit breakers by flipping them both OFF and ON 2-3 times and then recheck the dryer for heat. If it continues to run and not heat then the voltage supply will need to be checked and confirmed before proceeding to test each component connected in a series circuit with the heating element for continuity using an Ohm meter. I do not recommend checking voltages unless you have experience and you feel safe and confident in doing so; otherwise I recommend calling for service. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: [Sears Home Services | http://www.searshomeservices.com?sid=MMLxexpertxmerch] .

Read More
Joey S -
Sears Technician
July 29, 2011
A:

Have a kenmore gas dryer that will not heat. I just replaced the ignitor and it still does not fire up. Can you offer and suggestions??

Read More
chuck -
December 21, 2011
A:

Chuck: Without having the model number of your gas dryer I can only provide general information. You will need to disconnect each one of the components connected in the circuit to the gas valve and igniter and check them for continuity. One of them is open which is breaking the electrical circuit to the igniter. Reply with the model number and I can provide model specific information and trouble shooting assistance.

Read More
Joey S -
Sears Technician
December 22, 2011
A:

The model number is 110.76944501

Read More
chuck -
December 22, 2011
A:

Chuck: Thank you for adding the model number. You did not mention if the new igniter is glowing red or not. If it is not glowing then we must assume the igniter is not getting any voltage. If it is not glowing then it could have a faulty thermal fuse, operating thermostat, high limit thermostat or a faulty flame sensor. I recommend checking the thermal fuse first. The thermal fuse is located on the blower wheel housing and will have a solid red wire and red wire with a white stripe connected to it. Disconnect both wires and check across the two male terminals on the thermal fuse for continuity. It must measure continuity or it is faulty. Disconnect the power cord from the power source before servicing your dryer.

Read More
Joey S -
Sears Technician
December 22, 2011
A:

Ignitor does not glow. I replaced the thermal fuse and still no luck. I am going to replace the operating thermostat. Hoping for the best. What do you think??

Read More
chuck -
December 22, 2011
See more answers
Q:

how do i remove the front 2 panels on my kenmore model 11068942892

A:

Good afternoon.... I can appreciate your wanting to do your own work and save yourself $. I did locate a link that will discuss a different task (replacing a motor) but will guide you to where you want to go. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will enable you to address and complete the task before you and have a nice day.

Read More
Henry -
December 13, 2012
A:

Thanks for contacting ManageMyLife.com. I see Henry provided you an answer above with the image to remove the panels. Click on the image below to view the information.

Please feel free to let me know if you need further assistance.

Thank you for using ManageMyLife.com.

Read More
Jonathan B -
Sears Technician
December 13, 2012
See more answers

Top Parts