Model #11067732791 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Dryer 11067732791 timer

A:

Thank you for your question.  I am sorry for the problem with the Kenmore 11067732791 Dryer timer installation.   I found on instruction sheet and I assume you did not get one with the part.  The timer terminals should be color coded.  Which color wire or wires do not have a terminal?   Reply below with which color wire or wires have not place to go and I will try to assist you in completing this project. 

 

Read More
Fred M -
Sears Technician
August 19, 2013
Q:

electric dryer timer

A:

It can be a real headache when the timer on your dryer fails to operate properly, even after replacing the part. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner

Read More
Julio -
February 14, 2013
A:

Thank you for your question and I understand your concern.

You did not clarify if the timer continues to advance after the off position in the Time Dry or the Automatic Dry cycles. 

Once the timer has been installed, it cannot be returned.

The timer motor has two leads, one lead is connected to terminal BK on the imer and timer terminal BK has line one (L1) power source at all times as long as the dryer is plugged in. Now, the other lead is the Neutral side and it is connected to timer terminal TM.  Timer terminal TM will close timer contact TM and timer terminal WB in the TIMED DRY settings which supplies nuetral to the timer motor through door switch and motor centrifugal switch contacts 5M and 6M once the motor is running which completes the neutral path to the timer motor and it will advance all the way through to the OFF positon. When it reaches off, timer contact BK and BU will break/open which causes the dryer motor to shut off. Once the motor shuts off, the motor centrifugal switch contacts 5M and 6M opens and breaks the nuetral to the timer motor at which time the timer motor quits running.

Does the heating element come on when you set the timer to TIME dry without starting the dryer? If so, the motor centrifugal switch contacts 2M and 1M are likely stuck/welded shut meaning the motor will need to be replaced.

I added an image below of the wiring diagram. I traced the timer motor circuit. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
February 15, 2013
A:

when the dry is on time dry cycle the timer keeps ticking till it reaches off on auto dry cycle. when the dryer is on auto dry cycle it stops when auto dry cycle is done. the heating element does not come on until the start button is pushed.i opened the origanal timer to look inside and none of the contacts were stuck in closed position.

Read More
joseph -
February 15, 2013
A:

Joseph; Double check the timer wiring. The image I provide of the wiring diagram with have a chart at the top indicating which timer contacts should open or close based on the cycle selected. I would test the timer contacts using an Ohm meter. You could have a faulty new timer if the timer is wired correctly. Be sure to disconnect the power cord before disconnecting the wires from the timer and test tosee if the contacts are opening and closing per the timer chart.

Read More
Joey S -
Sears Technician
February 15, 2013
A:

i connected the wires to the new timer in the same position as the old timer, and i checked to see if their correct with the diagram you sent me, it is wired correct.the old timer kept ticking past timed dry till it got to off position of auto dry cycle, that is why i replaced timer in first place. is there some other problem that could have caused the timer to continue ticking till it gets to auto dry off position?

Read More
joseph -
February 15, 2013
A:

Joseph: Disconnect the power cord and remove the heating element to see it's broken or shorted to heater housing.

Read More
Joey S -
Sears Technician
February 15, 2013
A:

the dryer gets hot maybe too hot, i did replace the thermal cut-off kit last year sometime,when dryer did not heat-up, and had heating element checked at parts store it was good. could the cut-off kit be bad again?

Read More
joseph -
February 15, 2013
A:

Joseph: A faulty thermal cut off would prevent the dryer from heating. Have you looked at the wiring diagram I provided? Did you remove the heating element and see if it was shorted to ground?? Maybe you should call a service technician and have him come out and diagnose the problem.

Read More
Joey S -
Sears Technician
February 15, 2013
A:

yes i have checked out the diagram you sent me, and i have clothes in the dryer ,work clothes so when thier done ill check heating element . thank you for information about thermal cut-off. i just needed to know if there was something i could do myself to resolve the problem,so i,ll check to see and hopefully i can fix without calling service tech, again thank you

Read More
joseph -
February 15, 2013
A:

i removed the heating element to look at it, it seems to be in operation no broken coils but one wire that connects to the element seems to be a bit coroded i twisted the wire and some corosion dust fell off. i then reinstalled element and still have same problem

Read More
joseph -
February 17, 2013
See more answers
Q:

timer on electric dryer keeps ticking after cycle is done

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina -
February 16, 2013
A:

Hi,

Thanks for contacting ManageMyLife. I understand how frustrating it is having trouble with your appliance not working.

The timer motor runs through the timer and the neutral for the timer motor is the WB or the OR contacts.  At each off position the WB or the OR contacts open up and the timer stops.  If this is not the case I would look for a problem with the new timer keeping the WB or the OR contacts closed.  If the timer contacts are opening then I would check the wiring harness for a short in some of the wires.  Also check the orange wire to the heater from the timer.  In the wire there is a 5000 ohm resistor and it could be the cause of the problem.

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
February 18, 2013
A:

bill, thank you your answer has givin me good direction,the diagram is clearer with your highlighted marks. i located the inline resistor on the orange line to heater,when i cleaned the lint and dust off of it i could see the plastic cover looked burnt on backside , so i have ordered a replacement kit from SEARSPARTSDIRECT online and i will have the part delivered soon,thank you again ill let you know how it turned out. joe

Read More
joseph -
February 21, 2013
A:

Your Welcome, Keep me posted.

Read More
Bill__W -
Sears Technician
February 22, 2013
A:

hello again, well i replaced the inline resistor and still timer keeps ticking past off on timed dry,and stops at off position of auto dry.this is the same problem with old timer, i will replace new timer with the old one and see if new timer is checked out at parts store. anything else i should check out?

Read More
joseph -
February 22, 2013
A:

The contact tm to wb opens and tm to or is the cool down in the timed dry part of the cycle then it should open at the off position. of the timed cycle not drive through the cycle.

Read More
Bill__W -
Sears Technician
February 22, 2013
See more answers

Top Parts