Model #11067642600 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Dryer does not cool down even when cycle is done

A:

I know how important it is to have a good working dryer in the home so that you can dry your freshly washed clothes. I am adding a link below that will help you check the heating element. I also think that the heating element staying on sounds dangerous and I am adding a second link in where you can set service to have a certified tech come out and check the dryer. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
March 20, 2012
A:

From the description you give I suspect the element has broken and is now grounded to the cabinet. If this happens then the element can stay hot even if the dryer is not running. I can provide more information how to access and check the element if a model number is supplied. The following link shows a typical Kenmore dryer: Kenmore Elect Dryer . This may not be your dryer. Please reply with a model number for further assistance.

Read More
Fred M -
Sears Technician
March 21, 2012
A:

The model number is 110.67642600. Tonight I got the back of the dryer off and accessed the element. When I started to slide the element out, it got caught on a little metal barb. I'm hoping that was where it shorted out. The element looks completely intact. The part of the coil that caught on the metal barb obviously bent a little, but I was able to bend it back. How do I check to see if the element is any good or not?

Read More
Brian Brand -
March 21, 2012
A:

Upon further review of the heating element, The plate running down the middle of the element is bent up where it was caught on that barb. That plate also shows considerable wear (scratches) from the hot element scraping up against that plate. Starting about 1/2 way down the heating element where the plate isn't bent, there are no scratch marks.

Read More
Brian Brand -
March 21, 2012
A:

If the element heats when the timer is turned on but the motor is not running then the element is likely grounded. The 279838 element is available from the following link: [ 279838 Element for Kenmore dryer model 110.67642600 | http://www.searspartsdirect.com/partsdirect/part-number/279838/0026/110&pathTaken=partSearch&blt=14&prst=0&shdPart=279838?sid=MMLxexpertxmerch] . I hope this helps. Thanks for asking the question.

Read More
Fred M -
Sears Technician
March 23, 2012
A:

This link to the element should work for you. [ 279838 Element for Kenmore dryer model 110.67642600 | http://www.searspartsdirect.com/partsdirect/part-number/279838/0026/110&pathTaken=partSearch&blt=14&prst=0&shdPart=279838?sid=MMLxexpertxmerch ]

Read More
Fred M -
Sears Technician
March 24, 2012
See more answers
Q:

Our eletric kenmore dryer Model 110.67642600 wont turn on

A:

I'm sorry about the difficulties that you are experiencing with your Kenmore Dryer. I did some research at Managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond to your specific question. I have attached the link below. If you decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
April 13, 2011
A:

Thank you for your question and I understand your concern.

To start with, the first thing to check and confirm is the voltage supply. Your electric dryer requires the proper voltage to start. The motor only needs 110-120 volts to start but the dryer will need 220-240 volts in order to start and heat. The voltage should be checked and confirmed at the back of the dryer where the power cord is attached. You will need to remove the terminal block cover and test the voltage supply across the two outside terminals and then across each outside terminals to the center terminal. The voltage supply must measure 220-240 volts when measuring across the two outside terminals and the voltage must measure 110-120 volts when measuring across each outside terminal to the center terminal. NOTE: I do not recommend checking and confirming voltage unless you have experience and feel safe and confident in doing so, otherwise I recommend calling a service technician to diagnose and repair your dryer.

If the voltage supply is correct, then next thing to check is the thermal fuse. The thermal fuse (key#59) is mounted on the blower housing. The thermal fuse can be disconnected and tested for continuity using an ohm meter. See image below for thermal fuse location. Remove the rear panel to access the thermal fuse. Disconnect the power cord before removing and disconnecting the thermal fuse. If the thermal fuse doesn't measure any continuity, replace the thermal fuse. The part number of the thermal fuse is 3392519 and it can be ordered from Sears PartsDirect

I added YouTube video showing how to test the thermal fuse using an ohm meter.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services

Read More
Joey S -
Sears Technician
April 14, 2011
See more answers
Q:

my Kenmore 600 Series Dryer will not start on any setting. I have power because the light comes on when the door is open. The lent trap and vent pipe were clean

A:

Laundry is a chore that has to be done, so having a dryer that is working makes life a lot easier. I found this link on the website that will give you some guidance on what could be wrong. I attached the link below, good luck!!!

Read More
Raquel F -
October 19, 2010
A:

From what you're describing it sounds like the thermal fuse needs replaced. First disconnect power to the dryer. Pull the dryer out & remove the rear panel. Pull the 2 wires off of the thermal fuse. Use an ohmmeter to check the continuity of the thermal fuse. If the thermal fuse reads no continuity (open) then you will need to replace the thermal fuse. The thermal fuse is a safety device that will shut the unit down if an overheating condition occurs. This means we will need to check the heating element & the exhaust venting that runs outside the house. I am sending you step by step instructions from the service manual to access & make the needed checks to the dryer. You can remove the element for inspection or use an ohmmeter to check it. The ohms value should be between 7-12ohms on most heating elements. You can use a leaf blower to blow out the vent line if needed. Another possibility; motor, timer or wiring problems.

Please click on the image provided in the attachment below.

Read More
biker dave -
Sears Technician
October 20, 2010
See more answers

Top Parts