Model #11067442600 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Why doesn't my dryer want to shut off?

A:

You didn't mention which cycle that you were using (auto or timed). If the timer will not advance in the auto cycle try it in the timed cycle. If it advances okay in the timed cycle (even though it may not shut off at the end of the cycle) then you likely have a problem with the orange wire that runs from the heating element to the timer (shown outlined in orange on the wiring diagram below). The most frequent cause of this failure is that this orange wire has been detached from the heating element. If this is the situation, then reconnecting this wire will often fix this dryer problem. To check this wire, unplug the dryer and remove the back panel. The location of the components in the back of the dryer is shown in the second image below. Check the orange wire that should be connected to the heating element terminal.

If the orange wire is connected properly to the heating element, you can access the timer in the console (with the dryer still unplugged) to check the wiring connections in that area. The third image below shows how to release the clips that secure the console to the top panel in this type of dryer. Your dryer will look slightly different but the access procedure is the same. Check the connection of the orange wire on the timer. If the connection is okay then you could have a break in the wiring.

Several other problems could prevent the dryer from shutting off or the timer from advancing. In a timed cycle, the white/black wire provides the path to the L2 leg to advance the timer (the timer motor is a 240 volt version in this dryer) as shown by the red outline in the wiring diagram below. A heating problem would also prevent the time from advancing. An open or shorted heating element could interrupt the path shown through the yellow and orange outlined route below. These latter failures are rare but possible.

These tips should help you determine the cause of your dryer failure. If you need more help, resubmit your question with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 16, 2010
A:

I have a Kenmore Model#11062722100 and it won't shut off in the timed dry cycle would my solution be the same?

Read More
Anonymous -
June 14, 2012
See more answers
Q:

problem with clothe dryer. All of the sudden it stopped working. I replaced the start button but it still doesn't work.

A:

I know how important it is to have a good working dryer in the home so that you can dry your freshly washed clothes. While you are waiting for your expert answer, I did manage to find a link that will provide you with some information to help you with your question. I hope my link is useful.

Read More
Joseph P. -
July 18, 2011
A:

Hi Cesar,

Thank you for submitting a question to Manage My Life.

I am sorry you are having problems with your dryer.

You can try bypassing the door switch to see if the dryer will start. Here is a video that will demonstrate how to gain access to the lid switch; Video . This video is for demonstration purposes only. This washer may not look exactly like yours, but the procedure is basically the same. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

To bypass the lid switch you will need to disconnect the door switch harness and place an insulated piece of wire between the outside wires (colored wires) on the console side (see image below). Tape this in place with electrical tape to make sure it will not come into contact with anything else. Plug the dryer back in and try to start a cycle. If the dryer starts you need to replace the door switch. Do not leave the bypass wire in place. This is for testing only.

I have also included a wiring diagram below.

The diagnosis of this issue will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have an ohm/volt meter and are confident in your technical abilities, please reply below and I will be happy to give you the checks.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

Please perform the diagnostic tests detailed here and report back with your findings. I am looking forward to assisting you again in the near future.

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
July 19, 2011
See more answers
Q:

Do I need to replace the circuit breaker for my Kenmore 400 series electric dryer?

A:

When the L2 (line 2) circuit breaker trips your dryer timer will quit advancing as well as quit heating. Unplug the dryer and then see if the circuit breaker will reset. If it resets, set the timer to NO heat or AIR fluff and then reconnect the power cord and start the dryer. If it runs without tripping the breaker then set the timer and temperature switch to HEAT and see if trips the circuit breaker. If it trips it immediately, the heating circuit could be shorted to ground. If it begins to heat for a short time and then trips the circuit breaker, it could be a weak circuit breaker.

You can access the heating element/circuit by unplugging the power cord and removing the rear panel.

I recommend calling a service technician to diagnose the failure.

Read More
Joey S -
Sears Technician
November 27, 2009

Top Parts