Model #11067322600 KENMORE Residential Dryer

  • Cabinet Parts
    3 Results
  • Top And Console Parts
    3 Results
  • Bulkhead Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

No heat won't does not shut down 11067322600 Kenmore Residential dryer

Q:

idler pully 11067322600 Kenmore Residential dryer

A:

 

Thank you for choosing Sears Parts Direct. I can certainly understand how frustrating it can be when needing to install the idler pulley on your dryer. I did look into the model number you have provided and I have found instructions on where it is installed.

Make sure your unit is off before working on it.

1. Lift up the lint screen cover and remove the screws.

2. take a putty knife and release the top of the washer lid. Go above the tabs to release.

3. Release the wiring harness and remove the front screws holding the front panel. Take front panel off.

Here is the link to a video that will show you where the idler pulley goes.

 

Thank you for your question. Have a great day.

Read More
Natasha12 -
Sears Technician
October 31, 2013
A:

Thank you so much that was most helpful. Have a great day. :-)

Read More
Mark72450 -
October 31, 2013
A:

That is great to hear I am glad you were able to get your unit back up and running. Thank you for choosing Sears Parts Direct.

Read More
Natasha12 -
Sears Technician
October 31, 2013
See more answers
Q:

My dryer won't start

A:

While you are waiting on an expert to answer your question, a suggestion I have is to add more specific detailed to this thread so you can get a better answer from the experts!

Read More
Dezeray S -
January 10, 2011
A:

I have a Kenmore model #110.67322600 that is three years old. It was working fine and then out of the blue just didn't start. Any suggestions?

Read More
M Hoffman -
January 10, 2011
A:

On something like this we need to make sure the unit is receiving power first. Since this is an electric dryer you will have a double 30 amp breaker providing power to the wall outlet for the dryer. Turn both breakers off & then back on, this will reset the breaker.

Now you can check the dryer operation. If the dryer is still not coming on we will need to make some checks with an ohmmeter to find the root cause of the problem.

First, disconnect power to the dryer by unplugging the power cord.

In the image provided follow the rear panel removal instructions, use caution for sharp metal edges. You will see the thermal fuse on the left side mounted to the blower housing, it has 2 blue wires. You can either jump the thermal fuse by connecting & taping the 2 blue wires together or use an ohmmeter to check it. The thermal fuse should read closed continuity on your meter. If the dryer starts after this test then we know the thermal fuse failed. The thermal fuse will fail if the dryer overheats due to a blocked vent or shorted heating element. You can use your ohmmeter to test the heating element; with both wires removed place your meter leads across the 2 terminals, you should read between 7.8 to 11.8 ohms.

If the heating element checks good you will need to have the exhaust venting cleaned out to prevent overheating & tripping the thermal fuse. If you find the thermal fuse without continuity it is bad & will need to be replaced.

Another possibility is the door switch, open the door & manually push in on the door switch; you should hear it click if it is working properly. If the door switch needs to be replaced I am sending you access instructions for that also. First, remove the 2 screws hidden under the lint screen compartment. Use a putty knife to release the hold down clips between the top & front, see image below. You will see the door switch on the right side. Follow the instructions for replacement.

Another possibility is the motor or a wiring harness problem.

After making these initial checks please report back your findings if you still need assistance. Thank you.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: sears home service

Read More
biker dave -
Sears Technician
January 11, 2011
See more answers

Top Parts