Model #11066924500 KENMORE ELITE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers


Kenmore Elite Electric Dryer 11066924500 Kenmore Elite Residential dryer


Thank You for contacting I do apologize for the delay in answering your question.

This is a very simple do-it-yourself project. There are two release clips between the bottom panel and the cabinet drum. You can use a putty knife to release these clips and then pull the bottom panel foreward.

If you need further assistance, please resubmit your question with additional details. Thanks for visiting

Read More
Desirea -
Sears Technician
March 24, 2014

Kenmore Elite Electric Dryer - Drum seal replacement directions. 11066924500 Kenmore Elite Residential dryer


Hello glad to help.  Thank You for choosing Sears

I am sorry and do understand your frustration when doing repair work on the dryer.

Glad to help out.   Im  looking at your model Kenmore number 110.66924501.


1.  Please be safe and first disconnect the power cord and pull the dryer at least 6 inches or so foreward.

2.  Remove the screws holding the back of the top panel in place.  Pull the top panel back and up to remove it.  May have to use something like a putty knife under the seam along the front of the cabinet for the panel.  Pull up on the handle of the knife to release the top panel away from the cabinet piece.

3. Lift the top of the dryer off the cabinet.  Place the top, control panel piece, and lean the top against the wall behind the dryer.

4.  Take out the screws from the top front corners.  Pull the wire harness that connects the door switch to the rest of the dryer and set it apart someplace safe.  

5.   Look inside the dryer and underneath the right side of the drum to find the pulley holding the tension on the dryers drum.  Think about taking a digital photo showing the way the drum belt threads around the pulley so you will remember when you have to reinstall it.

6.   Push the idler pulley away from the drum and will release the tension.  Pull the belt away from the idler pulley then from the motor pulley.

7.   Grab the belt at the top of the drum with one hand.  Grab the drum with the other hand.  Pull the drum straight out of the dryer cabinet.

8.   Pull off the rear seal.  The seal probably wont come off easy in one piece, might leave bits and pieces along the edge of the drum.   Use some fine grit sandpaper to remove any of the seal particles left.  Wipe the edge of the drum clean with a liquid adhesive remover.   Wipe the drum dry with some paper towels.

9.   Position the seal where the edge with the stitchin faces the front of the drum.   Apply a vhin coat of high-heat adhesive to the drum along the exterior edge.

10.  Press the new drum seal into the adhesive.   There is a small lip on the underside of the seal that sits against the outer edgeof the drum and helps you install the seal evenly on the rear of the drum.  Allow the high-heat adhesive to dry for about 2 hours.

11.  Do both seals then put belt back on and reverse the project to put everything back together.

Good luck.

 If you have further questions please let me know.

Thanks for choosing Sears


Read More
Larry L -
Sears Technician
October 17, 2013

Attach Kenmore Elite Dryer, Model 11066924500, to a Pedestal, Part W10154785


I can certainly understand your concern over the issue that you are having with the dryer and pedestal. I was able to locate a few things that might help while you wait for the expert to answer you question more specifically.

Read More
celene -
January 07, 2011

As stated before in the previous question the pedestal will not fit this particular dryer. This style dryer was matched with a top load washer and there was never a pedestal designed to fit this model.

The parts person must have completely misunderstood what you had or what you wanted. I haven�t heard of this happening before.

I hope the phone number I gave you helps with this problem but please reply and let me know. I will make a few checks on Monday if there are any options for you to pursue.

Read More
Fred M -
Sears Technician
January 09, 2011
See more answers

Top Parts