Model #11066904692 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Need to reattach Power Cord to Dryer. There are 3 terminals. Not sure where the red, white and black cords attach onto the panel 11066904692 Kenmore Electric dryer

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when needing to work on the dryer.
 
Glad to help out.   Im  looking at your Kenmore Dryer model number 11066904692.

Instructions on plugging a 3 prong plug to dryer:

1.  Don't plug it into the wall until it is safely wired into the dryer.

2.  Undo the bolts at the top back side square piece called the access plate.  

3.  Connect the 3 cords to the terminal block and screw them in.  The green wire is the ground wire.  Attach the red wire to the right post, the black wire to the left post, and the green wire to the middle post.     Most important just put the middle cord wire in the middle connection of the dryer.   The other two wires can be hooked up either way.  

4.  Bolt/screw the wires down good then you can replace the back plate and be ready to go.


Read More
Larry L -
Sears Technician
April 03, 2014
Q:

Kenmore 90 Series Clothes Dryer

A:

We depend so much on our dryer for our family use. It's frustrating when they stop working. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view. I hope the link that I provided is helpful. Have a nice day!

Read More
Yadira B -
September 05, 2012
A:

Thank you for submitting your question. Yadira has provided you with great information for your symptom. If the heating element test good, then the second part that would cause this is the operating thermostat (3387134). You can order all parts from our Sears Parts Direct web site. If you have to replace the operating thermostat follow these instructions. First remove all power from the dryer . You'll access the thermostat by removing the back panel. The operating thermostat (part 3387134) is on the blower housing on the bottom left side of the dryer. It's labeled as the "thermistor" in the image below but on your dryer it's the operating thermostat. To replace this component, pull the wire connections off of the thermostat (with the dryer still unplugged) and remove the screw that secures it to the blower housing. Mount the new thermostat and connect the wires. I hope this helps. Please reply back to this thread if you require further assistance with this repair. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
September 07, 2012
See more answers
Q:

Kenmore 90 series dryer

A:

Troubleshooting dryer issues can be challenging and a second opionion from an expert makes sense. While yoiu wait for the expert to review this model and respond, I did locate two similar questions that may help. I attached the links below. I hope this is helpful.

Read More
Barbara H. -
March 01, 2012
A:

Thank you for your question and I understand your concern.

Based on your symptom and details I suspect the motor is getting too hot and tripping out on the motor thermal overload. Once the motor cools down enough the thermal overload resets and it will run again until the motor thermal overload trips again. Replacing the motor should resolve the problem.

I added a YouTube video with the motor replacement procedure. The part number of the motor is 279787 which can be ordered from Sears PartsDirect .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
March 02, 2012
A:

Thank you, Looks like i was thinking right, Only problem i encountered was getting the blower wheel off, if split when I tried to remove it as per the video, have one on order now! Thanks again for your great help.

Read More
Chris -
March 06, 2012
See more answers

Top Parts