Model #11066514694 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What is the cubic feet of my Kenmore dryer

A:

When it comes to figuring out the measurements of an appliance can be challenging. While you are waiting for a detailed reply from an expert I have attached a link below that you may find helpful towards your question. Hope this helps!

Read More
Priscilla V -
March 25, 2012
A:

Thank you for your question and I understand your concern.

Your model dryer is rated at 5.9 cu. ft.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
March 26, 2012
See more answers
Q:

electric dryer wont start

A:

I found a question in Manage My Life under the Answers button that was similar to the question you asked. I think this information will be helpful to you. I attached the link below. Hope this helps!!!!!

Read More
Raquel F -
July 13, 2010
A:

From the description you give I suspect the problem is with the motor.

This can be a difficult problem to pin down since the problem only occurs when the dryer is hot.

At that point a technician could quickly remove the front panel and check voltage across the motor and if there is 120 volts then the motor is bad.

Live voltage is not something I suggest be done by anyone except a technician.

One thing you might try is to access the motor, remove the belt and then try the motor and see if it will run.

The images below will help you with removing the front panel to access the motor and belt. Remember to unplug the dryer first.

If the motor starts with no belt then the problem might be with the drum rollers or felt seal creating a drag when hot.

The 279827 motor is available from the following link: Sears PartsDirect for approximately $109 dollars.

The 2nd image will help if you do-it-yourself.

The following link shows a similar electric dryer so you can compare repair verses replacement: New Similar Dryer .

I hope this helps to resolve this problem for you.

Read More
Fred M -
Sears Technician
July 16, 2010
See more answers
Q:

How do I replace the belt on my Kenmore dryer model 110.66514694?

A:

How do I replace the belt on my Kenmore dryer model 110.66514694?

  • Prepare for replacing the dryer belt by lifting the lint-screen cover on the top of the dryer. Then remove the lint screen. Skip this step if your lint screen is inside the door. Remove the 2 Phillips screws inside the door instead.
  • After removing the lint screen, lift the cover and remove the screws that hold the lint-screen housing to the dryer top.
  • Slide a putty knife between the front panel and the top near a corner. Lift the corner and repeat on the other side.
  • To remove the lower panel, insert the putty knife between the panel and each side. Then twist to release clip.
  • Place a few wood blocks under the drum. These support the drum when the front panel is moved away from the sides.
  • Loosen the screws that secure the bottom of the front panel to the dryer sides. Do not completely remove the screws.
  • Remove the screws that secure the front panel to the dryer sides at the top. These are accessed from the inside of the cabinet.
  • Lean the front panel away from the sides and slip the new dryer belt over the drum. Then resecure the front panel.
  • Check that the lip on the back of the dryer drum fits properly against the seal on the rear bulkhead of the dryer.
  • Locate the original position of the old belt, and slip the new belt in place. Keep the grooved side of the belt down.
  • Push the idler pulley toward the motor and loop the doubled-up belt around the idler pulley. Slip belt around motor pulley.
  • Rotate the drum counterclockwise a few turns to check belt tracking. Then replace remaining components and test run.

Read More
Korinna S -
Sears Technician
January 03, 2010

Top Parts