Model #11065062500 KENMORE Residential Dryer

  • Console Panel Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • Dryer Top Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore 110.65062500 will not start 11065062500 Kenmore Dryer

Q:

Removing back panel of dryer 11065062500 Kenmore Dryer

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you in locating the instructions to replace the thermal fuse in your dryer.

I have attached to diagrams to assist you in getting access to your thermal fuse. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
June 18, 2015
A:
Natasha12 -
Sears Technician
June 18, 2015
See more answers
Q:

Kenmore Elite Sensor Smart Electric Dryer - 110.65062500 Won't Start

A:

Having an appliance not working properly can ruin anyones day. While you are waiting on an expert to answer your question, I found some great links in the Manage My Life website on your problem you are having with your appliance. I have attached the links below. Hope this helps!

Read More
Dezeray S -
April 09, 2012
A:

Thank you for your question and I understand your concern.

The thermistor can not be by passed on the control will think it is shorted. Do not attempt to by pass the thermistor.

I added an image below of some diagnostic information taken from the tech sheet. I also traced the motor circuit in red and green. If you hear the motor relay closing, and the motor is not starting could indicate a faulty thermal fuse. If the thermal fuse is faulty, the motor will not get the voltage needed to start and run. If the thermal fuse is not faulty, the control board is most likely faulty. I recommend disconnecting the power supply from the dryer and then disconnect and test the thermal fuse for continuity with an Ohm meter. If the thermal fuse is okay, you can confirm if the control board is faulty by checking the voltage across the terminal P1-4 and P1-2 and then across P1-4 and P1-3 after pressing START. NOTE: I do not recommend checking voltage unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your dryer.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 10, 2012
A:

Hi Joey, Thanks for the quick follow-up. I meant to say I jumped the thermal fuse and the problem still existed. I did not try to jump the thermistor as I knew this would short it out. I will get my hands on a multimeter and check the items you suggested. Thanks for your help! I'll be in touch. -Pete

Read More
Anonymous -
April 10, 2012
A:

Hi Joey, I apologize for the delay in response. As I mentioned before, I jumped the thermal fuse and the problem still existed so I performed the motor circuit test and measured the resistance across P1-3 and P1-4. The resistance was around 3 ohms so I ordered the electronic control board (P/N 8566150) and this fixed my problem. Thanks for your help and for providing me with the schematic.

Read More
Peter -
April 23, 2012
A:

Peter: Your welcome and thank you for using Manage My Life.

Read More
Joey S -
Sears Technician
April 24, 2012
A:

Joey/Newbie, Can either of you provide the schematic to change out the control board? Thanks! Carlos

Read More
Carlos -
June 16, 2013
A:

Hello Carlos. I posted a wiring diagram and a drawing of the control board in the first image below. The second image shows how to open the console on that dryer. UNPLUG the dryer before accessing internal components. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
June 17, 2013
A:

Hi Lyle - I can't thank you enough for the wiring diagram and drawing. The drawing was EXACTLY what I needed to access the control board located within the console panel. I actually used a credit card for each side of the front to release the clips that were holding the panel down. Once inside, the computer board was pretty much remove and replace. We now have a working dryer and no longer have to take our damp clothes to the neighbor's house. You're the best and deserve a 5 Star rating. All the best, my friend!!!

Read More
Carlos -
June 17, 2013
See more answers

Top Parts