Model #11064952300 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

How to remove push to start switch and back panel of dryer 110-64952300 110-64952300

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you in locating the instructions to replace the push to start on your dryer. 

 Remember to disconnect power to the dryer before any service or repairs.To open the console, pull the plastic end cap off of each side. Remove the hidden screw that you will find on each side under the end caps. Pull the console slightly forward and then hinge is up and back over the back panel. Once the console is opened, pull the knob off the push to start switch. Press the release clip. Once the tab is lifted, remove switch. Before removing the wires install the new switch. Then transfer the wires one at a time. After the new switch is installed, reassemble the dryer.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the unit before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

 

Read More
Natasha12 -
Sears Technician
August 10, 2015
A:
Natasha12 -
Sears Technician
August 10, 2015
See more answers
Q:

Kemmore Elite dryer 11064952300 with heating element not working after temp cut off replaced. 11064952300

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dryer and I do understand your frustration. Glad to help out. I'm looking at your model number 11064952300 and when you replaced the Heating element thermal cut-off I must assume you are also replacing the high-limit thermostat too that should come with the thermal cut-off. The thermal cut-off could be failing because of a restricted vent system or the heating element coil is broken and shorted to the heater housing which will cause the heating element to stay on if the timer is set while the motor is not running. 


I recommend checking the venting system for any restrictions or blockages and then removing the heating element to make sure its not broken and short to ground. Here is a link that may help with additional troubleshooting. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
February 04, 2015
A:

If the heating element works and tests for continuity does this not eliminate this issue ? Plus I have/can observe the heating coils heating up then turning off . Plus I see I replaced the heating coils in October of 14....Thanks, Dave Freeman

Read More
dtfreeman -
February 12, 2015
A:

And yes I did replace both parts included in the packet. The Thermal cut off and the high limit thermostat. Everything tests for continuity except the thermal cut off

Read More
dtfreeman -
February 13, 2015
See more answers
Q:

Heating coil install 11064952300 Kenmore Dryer

A:


Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you in locating the instructions to install the heating element on your dryer. 


Click here for videos. 





You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
October 07, 2014

Top Parts