Model #11064932200 KENMORE Residential Dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Dryer won't heat 11064932200 Kenmore Electric dryer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your dryer will not heat. 

How to test push to start switch:
To test this component, unplug the dryer and access the switch in the console. Check the continuity through the contacts where the blue wires are attached. Without the button pushed, you should measure infinite resistance (open). Push the button and hold it in. Measure the resistance through the leads with the button pushed in. You should measure near zero ohms of resistance (closed) while the button is pushed in. If not, then the switch is bad and will need to be replaced. 
3398095 part number for start switch.

The door switch could also cause the dryer not to start. 
 You can also check is to the door switch. You can open the dryer door & press in on the door switch with your finger, you should hear & feel a click. If the door switch is not responding you will need to replace it.
3406107 part number for door switch.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the unit before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

 


 
 

EXPERT






 

Read More
Natasha12 -
Sears Technician
August 09, 2015
Q:

No heat, all thermo-fuses and coil have continuity 11064932200 Kenmore Electric dryer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your dryer will not heat. 

How to test push to start switch:
To test this component, unplug the dryer and access the switch in the console. Check the continuity through the contacts where the blue wires are attached. Without the button pushed, you should measure infinite resistance (open). Push the button and hold it in. Measure the resistance through the leads with the button pushed in. You should measure near zero ohms of resistance (closed) while the button is pushed in. If not, then the switch is bad and will need to be replaced. 
3398095 part number for start switch.

The door switch could also cause the dryer not to start. 
 You can also check is to the door switch. You can open the dryer door & press in on the door switch with your finger, you should hear & feel a click. If the door switch is not responding you will need to replace it.
3406107 part number for door switch.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the unit before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
August 09, 2015
A:
Natasha12 -
Sears Technician
August 09, 2015
See more answers
Q:

How do I get a diagram of my Kenmore electric dryer model number 110.69812990?

A:

I provided a wiring diagram of your dryer in the second image below. The first image shows how to open the cabinet. Your dryer does not appear to have the optional belt switch. If the drive motor starts and runs, then it is likely that you have a broken drive belt. You can use the procedure in the first image to unplug the dryer and lift the top panel to check the belt. If it is broken, then it will need to be replaced. You can view a full parts list diagram of your dryer and order parts on the Sears PartsDirect website.

If the motor is running, then it is normal for the dryer to be heating but it should be blowing air out of the vent in back of the dryer when the motor is running. You could have a clogged exhaust vent or a problem with the blower wheel if the dryer is not blowing air out of the exhaust. Disconnect the flexible vent hose behind the dryer and check for air movement out of the exhaust on the back of the dryer with this hose disconnected if the motor runs.

If the motor is not running, you likely have 2 failures since the dryer is heating without the motor running. The third image shows the wiring diagram for your dryer with the motor and heating circuits traced. The yellow line traces the heating circuit. The element will normally not heat unless the motor is running and the centrifugal switch contact 2M to 1M is closed. You could have a failed centrifugal switch or the heating element could be grounded to the metal dryer cabinet to cause the element to heat without the motor running. This could have caused the thermal fuse to blow. The red and green lines trace the motor circuit on the wiring diagram in the third image. The red line shows the start circuit. The green line shows the circuit once the motor is running and the centrifugal switch closes contact 5M to 6M to provide the neutral circuit as shown by the green line. This link of a previous answer provides troubleshooting and repair information for this type of problem: Why does the heating element on my Kenmore model 110.64932200 dryer come on before the dryer starts running?

This information should help you determine the cause of your dryer failure. If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
October 22, 2009

Top Parts