Model #11064842400 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

How do I remove the motor pulley?

A:

I'm not sure why you want to remove the drive pulley on your dryer. The factory installed pulley is made of metal and it shouldn't need to be replaced unless it damaged or has burrs in the grooves of the pulley. You do not have to remove the motor in order to remove the pulley.

To remove pulley:

  • There is flat spot on the motor shaft about 1 inch behind the pulley.
  • Use a crescent wrench on the flat spot to prevent the motor shaft from turning.
  • Use another crescent wrench to turn the motor pulley counterclockwise (CCW) while holding the motor shaft from turning.

Read More
Joey S -
Sears Technician
February 05, 2010
A:

would this procedure be the same for a crosley CDE6500W my pulley broke and my belt keeps on coming off?

Read More
Eric -
August 09, 2012
See more answers
Q:

Kenmore dryer #110.64842400 will not heat

A:

Your laundry situation can get quite complicated if your dryer isn't working properly. I researched your question and found some helpful links that may be useful to you. I hope link comes in handy!

Read More
Jackie S -
July 31, 2011
A:

Thank you Jackie S. Tom

Read More
Anonymous -
July 31, 2011
A:

Hi Tom,

Thank you for submitting a question to Manage My Life.

I know how frustrating it can be when appliances do not function properly.

Jackie S. gave you a link to one of my previous answers on this issue on a similar dryer. You can use this troubleshooting if you have a meter. This could be a bad timer, heating element, wiring/loose connection, motor centrifugal switch, or an open thermal fuse or thermostat. I have included a wiring diagram in the image below. The diagnosis of this issue will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have an ohm/volt meter and are confident in your technical abilities, please reply below and I will be happy to give you the checks.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

If I may be of further assistance as more details become available, please reply to this post.

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
August 02, 2011
See more answers
Q:

Kenmore Residential Dryer

A:

I'm sorry about the difficulties that you are experiencing with your Kenmore Residential Dryer . I did some research at Managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond to your specific question. I have attached the link below. If you decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
April 12, 2011
A:

When an electric dryer stops running all of a sudden the first thing to check and the most likely cause of the problem is an open thermal fuse.

You can remove the back panel to access the thermal fuse. See the image below to help with this.

The fuse can be checked for continuity with a meter is one is available.

It can also be checked by using a small piece of insulated wire to bypass it for a moment. Remove the two wires from the fuse and join them together with the small piece of insulated wire.

Read More
Fred M -
Sears Technician
April 13, 2011
See more answers

Top Parts